Pioneer VSX-933 Instruction Manual Download Page 111

Page: 111 / 131

111

≫

≫

≫

≫

≫

≫

• Do not use on the remote controller.

If an Error Message is Displayed

If an error occurs, "





Error!" is displayed on the display of the unit. ("



represents an alphanumeric character.) Refer to the following descriptions and

check.

Error Code

•



-01,



-10:

The USB storage device cannot be recognized. Check if the USB storage

device or USB cable is securely inserted to the USB port of the unit.

Connect the USB storage device to an external power source if it has its own

power supply.

•



-05,



-13,



-20,



-21:

The firmware file is not present in the root folder of the USB storage device, or

the firmware file is for another model. Retry from the download of the firmware

file.

•

Others:

After removing the power plug once, insert it to the outlet, and then start the

operation from the beginning.

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands