Pioneer VSX-933 Instruction Manual Download Page 50

Page: 50 / 131

≫

≫

≫

≫

≫

≫

•

To return to the previous screen, press

•

To display an album title, artist name and album art of a file in WAV format,

make the folder structure and file names as shown below when saving music

files. The album art can be displayed by saving a .jpg file to display on the

screen in the folder of bottom level. Note that a large volume of .jpg file may

take time to be displayed, or may not be displayed.

Folder 1

Artist name

Folder 1-1

Album name

file 1-1

file 2-1

file 3-1

Folder 1-2

Album name

file 1-2

file 2-2

file 3-2

.jpg file

• Characters that cannot be displayed on this unit appear with “



”

• The USB port of this unit complies with the USB 2.0 standard. The transfer

speed may be insufficient for some content you play, and sound interruptions,

etc. may occur.

• Note that operation is not always guaranteed for all USB storage devices.

• This unit can use USB storage devices that comply with the USB mass

storage class standard. Also the format of USB storage devices supports

FAT16 or FAT32 file system format.

❏

Device and Supported Format (

p51

)

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands