Pioneer VSX-933 Instruction Manual Download Page 103

Page: 103 / 131

103

≫

≫

≫

≫

≫

≫

Setting Item

Default Value

Setting Details

Pairing

Information

You can initialize the pairing information saved on

this unit.

Pressing ENTER when "Clear" is displayed

initializes the pairing information stored in this unit.

•

This function does not initialize the pairing

information on the BLUETOOTH wireless

technology enabled device. When pairing the

unit again with the device, be sure to clear

the pairing information on the BLUETOOTH

wireless technology enabled device in advance.

For information on how to clear the pairing

information, refer to the BLUETOOTH wireless

technology enabled device's instruction manual.

Device

Displays the name of the BLUETOOTH wireless

technology enabled device connected to the unit.

•

The name is not displayed when "Status" is

"Ready" and "Pairing".

Status

Displays the status of the BLUETOOTH wireless

technology enabled device connected to the unit.

"Ready": Not paired

"Pairing": Paired

"Connected": Successfully connected

•

Wait for a while if "Bluetooth" cannot be selected. It will appear when the BLUETOOTH

function is started up.

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands