Pioneer VSX-933 Instruction Manual Download Page 49

Page: 49 / 131

≫

≫

≫

≫

≫

≫

USB Storage Device

You can play music files stored on a USB storage device.

Basic Operations

Perform the following procedure when this unit is on.

1. Switch the input on the TV to the input connected to the unit.

Plug your USB storage device with the music files into the USB port either on

the front panel or rear panel of this unit.

Press USB and select "USB Front" or "USB Rear".

•

If the "USB" indicator blinks on the display, check whether the USB storage

device is plugged in properly.

•

Do not unplug the USB storage device while "Connecting..." is being

displayed on the display. This may cause data corruption or malfunction.

Press ENTER in the next screen. The list of folders and music files on the

USB storage device is displayed. Select the folder with the cursors, and press

ENTER to confirm your selection.

Select the music file with the cursors, and then press ENTER to start playback.

USB

/ / /

ENTER

Inputs

HDMI 1

HDMI 2

HDMI 3

INPUT

TV’s REMOTE

USB Front

The illustration shows an image.

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands