Pioneer VSX-933 Instruction Manual Download Page 78

Page: 78 / 131

Setup

≫

≫

≫

≫

≫

≫

System Setup

Menu list

You can configure advanced settings to have a more enjoyable experience with this unit. For operation details, refer to “Menu operations” (

p80

Input/Output

Assign

TV Out / OSD

Make settings for TV output and On-Screen Displays (OSD) that appear on the TV.

p81

HDMI Input

Change input assignment between the input selectors and HDMI IN jacks.

p81

Video Input

Change input assignment between the input selectors and COMPONENT VIDEO IN jacks and the

VIDEO IN jacks.

p82

Digital Audio Input

Change input assignment between the input selectors and DIGITAL IN COAXIAL/OPTICAL jacks.

p82

Analog Audio Input

Change input assignment between the input selectors and AUDIO IN jacks.

p83

Input Skip

You can skip inputs to which nothing is connected when selecting them with the INPUT

SELECTOR dial on the main unit or with the input selectors on the remote controller.

p83

Speaker

Configuration

Change the settings of connection environment of the speakers.

p84

Crossover

Change the settings of crossover frequencies.

p85

Distance

Set the distance from each speaker to the listening position.

p86

Channel Level

Adjust the volume level of each speaker.

p87

Dolby Enabled Speaker

Change the settings of Dolby Enabled Speakers.

p88

Audio Adjust

Dual Mono/Mono

Change the settings of multiplex audio playback.

p88

Dolby

Change the setting of when Dolby signals are input.

p89

Volume

Change the Volume settings.

p89

Source

Input Volume Absorber

Adjust the volume level when there are differences in volume level among multiple devices

connected to this unit.

p89

Name Edit

Set an easy name for each input.

p89

Audio Select

Select the priority for input selection when multiple audio sources are connected to one input

selector.

p90

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands