Pioneer VSX-933 Instruction Manual Download Page 35

Page: 35 / 131

≫

≫

≫

≫

≫

≫

Connecting an Audio Component

This is a connection example of an audio component. Connect a CD player using

a digital coaxial cable or analog audio cable. You can also connect a turntable

that has an MM-type cartridge to the PHONO jack.

•

If the turntable has a built-in phono equalizer, connect it to any of the AUDIO

IN jacks other than the PHONO jack. Further, if the turntable uses an MC type

cartridge, install a phono equalizer compatible with the MC type cartridge

between the unit and the turntable, and then connect it to any of the AUDIO IN

jacks other than the PHONO jack.

If the turntable has a ground wire, connect it to the

GND terminal of this unit.

Analog audio cable ,

Digital coaxial cable

Turntable

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands