PRV-LX10
121
5
6
7
8
5
6
7
8
C
D
F
A
B
E
No.
Code Input
Operation/Usage
Remarks
53
[4]
USB TEST
USB devices must be connected to four ports.
Do not operate the connected USB devices
during the USB test. For example, if the
connected mouse is operated during the USB
test, the unit may hang up.
54
[5]
Error Rate TEST (Drive 1)
The error rate is measured at 0x30000 three times, and the
average value is judged. The command must be input during
playback stop.
ROM
Th value 3.3x10E-3
R, RW
Th value 3.3x10E-3
55
[6]
Error Rate TEST (Drive 2)
Effective when an optional drive is mounted
56
[7]
LTC display
Input TC is displayed on the FL display
57
[CLEAR]
Terminating result display
58
[ESC+[PAUSE]
[ESC]
Canceling Test mode
59
Shortcut command
60
[1]
V IN- Composite
61
[2]
V IN-S
62
[3]
V IN-Component (Beta)
63
[4]
V IN-Component (SMPTE)
64
[5]
V IN-DV
65
[6]
V IN-SDI
Effective when an optional board is mounted
66
[7]
A IN-RCA
67
[8]
A IN-XLR
68
[9]
A IN-DV
69
[0]
A IN-SDI
Effective when an optional board is mounted
70
[+10]
A IN-AES/EBU
Effective when an optional board is mounted
71
[TEST]
Target DRV - HDD
72
[CX]
Target DRV - DVD 1
73
[REP.A]
Target DRV - DVD 2
Effective when an optional board is mounted
74
[REP.B]
Target DRV - DVD 1 & 2
Effective when an optional board is mounted
75
[STEREO]
External Sync. OFF
Effective only during playback or recording stop
76
[P.RUN]
External Sync. NTSC
Effective only during playback or recording stop
77
[A.MON]
External Sync. PAL
Effective only during playback or recording stop
78
[SPEED-]
Progressive OFF
Effective only during playback or recording stop
79
[SPEED+]
Progressive ON
Effective only during playback or recording stop
80
[SIDE.A]
TC PORT - LTC
81
[SIDE.B]
TC PORT - RS-422A
82
[TV/LDP]
TC PORT - DV
83
[SCAN.F]
DV OUT ON
84
[SCAN.R]
DV OUT OFF
85
[x3 FWD]
REC
86
[x3 REV]
REC STOP
87
[STEP F]
Initialize
88
[STEP R]
Finalize
89 [ESC]+[OPEN/STOP]
Open/Close
90 [ESC+[DISP]
Display of data for debugging-Page 1: System data
91
[DISP]
To next page
Page 1: DVD-playback-related data,
FAN/PS-ON operation data, destination/region
data (DECB/DRV1/DRV2), GUID data
Page 2: DVD-playback-related data
Page 3: Decoding-related data (DECB)
Page 4: Encoding-related data (PCIB/AVIB)
Page 5: Encoding-related data (APL)
Page 6: Linux-related data
÷
How the [ESC] code is processed
• When the [ESC] code is received, ESCAPE mode is entered, but in
combination with the code(s) that follow(s), a specific meaning is added.
• ESCAPE mode is canceled if another code is received after the [ESC]
code.
• If [ESC] codes are received continuously, ESCAPE mode is retained.
÷
For playback-related operations, use the remote control unit supplied with
the main unit.
÷
The factory preset mode of the unit at power-on is Standby. To start up the
unit, press the [STOP] button, then press the [STANDBY/ON] button while
in Standby mode.
÷
If the error rate being measured is distinctly degraded because of
scratches on the media or defective media, a command cannot be sent
from the drive, and proper error-rate-measurement may not be performed.
If an error rate is not displayed, or OK/NG is not displayed on the monitor,
restart the PRV-LX10 (by resetting the drive) and perform the error-rate-
measurement again.
