Pioneer Elite SC-LX704 Instruction Manual Download Page 180

Page: 180 / 225

180

≫

≫

≫

≫

≫

≫

Full Auto MCACC

Place the supplied speaker setup microphone in the listening position, measure

the test tones emitted by the speakers, then the unit automatically sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. The influence of standing waves can be

reduced to suit the listening environment, the reverberation characteristics can be

measured to increase the precision of calibration, the speaker equalizers can be

adjusted, and the difference in phase and timing between speakers and speaker

units can be corrected. These settings and calibrations can be readjusted with

Manual MCACC, and you can enable or disable them in AV Adjust.

• Calibration takes between 3 and 12 minutes to be completed. The speakers

emit the test tone at high volume during measurement, so be careful of your

surroundings. Keep the room as quiet as possible during measurement.

• If you connect a subwoofer, check the power and volume of the subwoofer.

Set the subwoofer volume to more than half.

• If the power of this unit suddenly turns off, the wires in the speaker cables

have touched the rear panel or other wires, and the protection circuit is

working. Twist the wires again securely, and make sure they do not stick out of

the speaker terminals when connecting.

Select the connected speaker configuration.

Height 1 Speaker
Height 2 Speaker

Top Front

Top Rear

2 ch

Speaker B

Zone 2 Preout

Zone 2

7.1.4 ch

Zone Speaker

Note that the image on the screen changes each time you select the number

of channels in "Speaker Channels".

2. Place the supplied speaker setup microphone at the listening position, and

connect it to the SETUP MIC jack on the main unit.

SETUP MIC

When placing the speaker setup microphone on a tripod, refer to the

illustration.

Confirm a test tone is output from the subwoofer and press ENTER.

4. Press ENTER. Then, test tones are output from each speaker, and the

connected speakers and the noise in the surrounding environment are

automatically measured.

5. The measurement results in step 4 are displayed. If there is no problem in

the detection result of the speaker, select "Next" and press ENTER to output

the test tone again to automatically set the settings such as volume level,

crossover frequency, etc., to their optimum. (The test tone is automatically

output when 10 seconds has elapsed without any operation.)

• When an error message is displayed or when the connected speakers

cannot be detected, perform re-measurement by selecting "Retry" and

pressing ENTER.

• When it cannot be resolved by performing the re-measurement, confirm

if the speakers are connected correctly. If there is any problem with the

speaker connection, perform the connection after disconnecting the power

cord.

Once the measurement is completed, it is possible to perform the

measurement in 8 additional listening positions. To perform the measurement,

select "Next" and press ENTER, then follow the instructions. To not perform

the measurement, select "Finish (Calculate)" and press ENTER.

•

After each listening position is detected, select "Finish (Calculate)" and

press ENTER to complete the detection process.

Disconnect the speaker setup microphone.

Summary of Contents for Elite SC-LX704


































































































































































































































Search results

Summary of Contents for Elite SC-LX704

Reviews:

Related manuals for Elite SC-LX704

Brands by name

Popular brands

Pioneer Elite SC-LX704, Instruction Manual

Search results

Summary of Contents for Elite SC-LX704

Reviews:

Related manuals for Elite SC-LX704

Brands by name

Popular brands