PIAGGIO Liberty 50 Catalyzed Workshop Manual Download Page 58

Page: 58 / 165

- Disconnect the hoses (petrol-oil-vacuum-operated cock control).

WARNING

Handle fuel with care.

CAUTION

When installing the battery, first attach the positive cable and then the negative cable.

WARNING

Wear safety goggles when using hitting tools.

Removing the engine/shock absorber pivot pin

Remove the nut shown in the figure and then with-

draw the pin.

Reassembling engine to frame

Perform the disassembly steps in reverse order. Observe the prescribed tightening torques.

Locking torques (N*m)

Engine swinging arm pin nut

33 to 41

Engine/shock absorber

33÷41N·m

Engine from vehicle

Liberty 50 Catalyzed

ENG VE - 58

Summary of Contents for Liberty 50 Catalyzed






































































































































































Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands

PIAGGIO Liberty 50 Catalyzed, Workshop Manual

Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands