manualshive.com logo in svg

PIAGGIO Liberty 50 Catalyzed, Workshop Manual

Share
Download
PIAGGIO Liberty 50 Catalyzed Workshop Manual Download Page 151

Front wheel

FRONT WHEEL

Code

Action

Duration

1

003038

Front wheel axle - Remov. and refitt.

2

002011

Odometer movement sensor - Re-

placement

3

003040

Front wheel bearings - Replacement

4

003047

Front tyre - Replacement

5

003037

Front wheel rim - Removal and Re-

fitting

6

004123

Front wheel - Replacement

7

002041

Front brake disc - Replacement

Grease tone wheel or drive

Please take note that the code has been intro-

duced:

900001 - Tone wheel / drive greasing - 15'.

Never mistake the codes 002011 (movement sen-

sor replacement) and 005089 (tone wheel replace-

ment) in the event of noise of the indicated

components. The grease recommended is TUTE-

LA MRM 2 (soap-based lithium grease with Mo-

lybdenum disulphide).

In the following points we indicate with an arrow

the area to be greased (1 - Drive, 2 - Tone wheel)

Liberty 50 Catalyzed

Time

TIME - 151

Summary of Contents for Liberty 50 Catalyzed






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands