PIAGGIO Liberty 50 Catalyzed Workshop Manual Download Page 116

Page: 116 / 165

Fuel tank

• Remove the helmet compartment central cover.

• Undo the front and rear screws on the chassis

right side.

• Disconnect the breather pipe and remove the

float.

See also

Frame central cover

Front mudguard

• With the front wheel mounted, remove the fork

from the vehicle.

• Unscrew the 3 fixing screws and remove them.

• Slide off the odometer transmission and the

brake pipes, and then remove the mudguard.

N.B.

N.B. UPON REFITTING, BE CAREFUL TO PLACE THE 2
METAL CABLE GROMMETS CORRECTLY SO THAT THERE
IS NO RUBBING AGAINST THE WHEEL.

Chassis

Liberty 50 Catalyzed

CHAS - 116

Summary of Contents for Liberty 50 Catalyzed






































































































































































Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands

PIAGGIO Liberty 50 Catalyzed, Workshop Manual

Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands