PIAGGIO Liberty 50 Catalyzed Workshop Manual Download Page 57

Page: 57 / 165

Exhaust assy. Removal

- Remove the 2 fixing nuts from the manifold to the

head

- Undo the 2 screws fixing the silencer to the hous-

ing; then remove the whole muffler paying atten-

tion to the interference between its supporting

bracket and the cooling cover.

Removal of the engine from the vehicle

Removing the engine/connecting arm pivot pin

Remove the nut shown in the figure and then with-

draw the pin.

Disassembling engine from frame

-Disconnect the battery.

-Remove the muffler assembly.

- Remove the rear wheel.

- Remove the mechanical transmission of the rear brake.

-Disconnect the electric terminals.

- Remove the throttle grip and mixer transmissions.

Liberty 50 Catalyzed

Engine from vehicle

ENG VE - 57

Summary of Contents for Liberty 50 Catalyzed






































































































































































Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands

PIAGGIO Liberty 50 Catalyzed, Workshop Manual

Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands