PIAGGIO Liberty 50 Catalyzed Workshop Manual Download Page 113

Page: 113 / 165

Taillight assy.

• To remove the taillight and position light or the 2

turn signals, just unscrew the screws located on

the related light covers and disconnect the electri-

cal connections.

N.B.

REMOVAL OF THE REAR LIGHT BULBS IS ONLY POSSI-
BLE BY REMOVING THE LIGHT COVERS ROTATING
THEM 30° ANTI-CLOCKWISE.

Footrest

• Remove the shield back plate

• Remove the central frame cover.

• Remove the passenger footrest by undoing its

fixing screw.

• Undo the screw of the footrest lock and remove

the tab.

• Remove the 2 outer rubber covers of the footrest

fixing screws and undo them.

• Pull the footrest upwards paying attention to the

lower hooks.

See also

Frame central cover
Knee-guard

Liberty 50 Catalyzed

Chassis

CHAS - 113

Summary of Contents for Liberty 50 Catalyzed






































































































































































Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands

PIAGGIO Liberty 50 Catalyzed, Workshop Manual

Search results

Summary of Contents for Liberty 50 Catalyzed

Reviews:

Related manuals for Liberty 50 Catalyzed

Brands by name

Popular brands