manualshive.com logo in svg

PHOTO RESEARCH SpectraDuo PR-680, User Manual, Page: 33 / 149

Share
Download
PHOTO RESEARCH SpectraDuo PR-680 User Manual Download Page 33

PR-680/680L User Manual

 

22

 

 

A

DJUSTING 

P

OWER 

S

AVINGS 

S

ETTINGS

 

The 

Power Saving 

feature can extend the battery life if the instrument is left on and unattended.  The 

user can select to enable or disable this feature. 

1.

 

Touch 

Power Saving 

from the 

Preferences 

menu. 

 

FIGURE 26 - POWER SAVING MENU 

2.

 

The  current  status  of  the  Power  Saving  feature  is  displayed  in  the  window  adjacent  to 

Power 

Saving.

   In the  preceding example, 

Power Saving 

is enabled.  Touch this field to 

Disable

 Power 

Saving.  It will then read 

Disabled.

 

3.

 

To instruct the instrument to shut down after a pre-defined amount of time, touch the 

▼

 or 

▲

 

icons adjacent to the 

Turn power off after 

field.  Choices are 

1 to 30 minutes

 or 

Never

. 

4.

 

If you wish the screen to turn off after a pre-determined time, touch the 

▼

 or 

▲

 icons adjacent 

to the 

Turn screen off after

 field.  Choices are 

1 to 10 minutes 

or 

Never.

 

5.

 

Touch 

Back

 when finished making selections. 

 

A

DJUSTING 

B

RIGHTNESS AND 

C

ONTRAST

 

Brightness

  and 

Contrast

  control  the  appearance  on  the  display  under  various  ambient  lighting 

conditions.  To access and adjust Brightness and Contrast: 
 

 

FIGURE 27 - BRIGHTNESS AND CONTRAST SCREEN 

Summary of Contents for SpectraDuo PR-680






















































































































































Reviews:

No comments