manualshive.com logo in svg

PHOTO RESEARCH SpectraDuo PR-680, User Manual, Page: 24 / 149

Share
Download
PHOTO RESEARCH SpectraDuo PR-680 User Manual Download Page 24

PR-680/680L User Manual

 

13

 

 

1.

 

Facing the front of the instrument, slide the battery door 
latch away from the objective lens until the door opens 
(See 

Figure 17

). 

2.

 

Orient the battery so that the two copper contacts face 
toward the objective lens, and toward the rear of the 
instrument. 

3.

 

Gently insert the battery until it ‘clicks’ into place.

 

4.

 

Close the battery door.  Make sure the Battery Door 
Latch has engaged. 

I

NSERTING THE 

B

ATTERY

 

 FIGURE 18 - INSERTING THE BATTERY INTO THE PR-680/680L 

 

R

EMOVING THE 

B

ATTERY

 

 

1.

 

Facing the front of the instrument, slide the battery door 
latch away from the objective lens until the door opens 
(See 

Figure 17

). 

2.

 

Press the Battery Eject button located in the upper right 
hand  corner  of  the  battery  compartment.    The  battery 
will eject.  Remove the battery from the compartment. 

3.

 

Close  the  battery  door.    Make  sure  the  Battery  Door 
Latch has engaged. 

 
 
 
 
 

 

FIGURE 19 - REMOVING THE BATTERY FROM THE PR-680/680L 

 

 

Summary of Contents for SpectraDuo PR-680






















































































































































Reviews:

No comments