manualshive.com logo in svg

PHOTO RESEARCH SpectraDuo PR-680, User Manual, Page: 26 / 149

Share
Download
PHOTO RESEARCH SpectraDuo PR-680 User Manual Download Page 26

PR-680/680L User Manual

 

15

 

 

S

TANDARD 

O

BJECTIVE 

L

ENS

 

The standard objective lens for the PR-680/680L is the MS-75 - a 75mm f/2.8 MacroSpectar

®

 that focuses from 

1:4 magnification to infinity.  This objective lens enables the PR-680/680L to perform a variety of measurements 
including:  luminance,  radiance,  spectral  radiance,  chromaticity,  correlated  color  temperature  (CCT),  Color 
Rendering  Index  (CRI),  dominant  wavelength,  etc.

   

For  applications  other  than  radiance  or  luminance  the  PR-

680/680L can be supplied with optical accessories such as a cosine receptor for irradiance / illuminance, LR-127 
LED  Analyzer  for  testing  LED's    for  CIE  127  conformity,  fiber  probe  for  remote  non-line-of-sight  luminance 
testing, and a series of magnification lens for small spot size analysis.  Refer to Optional Accessory section for 
more information on all available optical accessories. 
 
 
 

 

FIGURE 20 - MS-75 OBJECTIVE LENS 

I

NSTALLING AND 

/R

EMOVING THE 

S

TANDARD 

L

ENS

 

The  standard  objective  lens  is  installed  by  aligning  the  thread  from  the  OBJECTIVE 

lens  with  the  instrument’s 

lens mount and rotating clockwise while grasping the rubber ring toward the rear of the lens (see 

Figure 20

). The 

thread should offer minimum resistance during installation. 
Full details including spot size versus working distance for all available lenses for the PR-680/680L can be found 
in the 

Specifications 

section. 

 
 
 
 
 
 
 
 
 
 
 

 

 
 
 

Uninstall Lens 

Install Lens 

Lens focusing ring 

Grasp here to install or 
uninstall lens. 

Summary of Contents for SpectraDuo PR-680






















































































































































Reviews:

No comments