- It can also be used to remove excess water from the baking tray or the dough.
slitter
- The slitter can be used to cut the dough and make slits in the top of the shaped dough of multi-shape bread.
Be careful when you handle the slitter. Its blade is very sharp.
Put the sheath back on the slitter after use and store the slitter in a safe place.
troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the
information below, contact the Consumer Care Centre in your country.
problems with standard recipes and possible solutions
Water or
milk
Salt
Sugar or
honey
Flour
Yeast
Other
Loaf rises, then falls Decrease 1-
2tbsp, use
colder liquid
Increase
¼tsp
Increase 1-2tbsp,
use fresher flour,
use right type of
flour
Decrease 1/8-¼tsp, use
fresh yeast, use right type of
yeast at right setting
Check power
supply
Loaf rises too high Decrease
1-2tbsp, use
colder liquid
Increase
1/4tsp
Decrease
½tsp
Decrease 1-2tbsp
Decrease 1/8-¼tsp, use right
type of yeast at right setting
Loaf does not rise
enough
Increase
1-2tbsp
Decrease
1/4tsp
Increase
½tsp
Use fresher flour,
use right type of
flour
Increase 1/8-¼tsp, use fresh
yeast, use right type of yeast
at right setting
Loaf is short and
heavy
Use fresher flour,
use right type of
flour
Add yeast, use fresh yeast,
use right type of yeast at
right setting
Check power
supply
Crust too light
Increase
½tsp
Select correct
settings
Loaf is uncooked
Check power
supply, select
correct settings
Loaf is overcooked
Decrease
½tsp
Select correct
settings
Bread mixture is
unmixed
Place bread pan
properly,
push kneading
blade correctly
onto shaft in bread
pan
Smoke comes out
of vents
Clean heating
element
High altitude
adjustment
Decrease
1-2tbsp
Decrease
½tsp
Decrease 1/8-¼tsp
Note: When you make corrections to amounts of ingredients, first change the amount of yeast. If the result is still not satisfactory, make adjustments to
liquids and then to dry ingredients.
problems with multi Bread shaper recipes
Problem
Cause
Solution
When shaping Multi Bread
Shaper breads, the dough has
a different shape than
described and shown.
The dough you started out with did not have
a rectangular shape and did not have a
uniform thickness
Flatten out the dough properly with a rolling pin to create a
rectangular shape with a constant thickness.
The dough tears easily and falls
apart (e.g. because it is lumpy)
and it is hard to shape.
You have not added enough water to the
mixture.
The dough was not properly prepared. Make sure you
follow the recipes.
You have worked on the dough too long
Knead the dough into a ball again and leave it to rest for 10
minutes. Then start shaping the dough from the beginning.
Knead the dough in two stages, with a 5-minute break in
between.
The dough is sticky and is
difficult to shape
You have added too much water to the
mixture or the water you added was too
warm.
Put some flour on your hands, but NOT on the dough or
the work surface. Then continue to knead the dough. Put
some more flour on your hands and continue until the
dough is less sticky.
EnglIsH
15
4222.005.0042.4.indd 15
02-06-10 14:29
Summary of Contents for HD9040
