Philips 107B50/74 Service Manual Download Page 63

Page: 63 / 75

V30 107B5

GENERAL PRODUCT SPECIFICATION

17" V30 GS4 107B5-86K CMTR

TYPE

: 107B50/74

BRAND : PHILIPS

8639 000 14235

2003-03-28

590

Go to cover page

Wayne Lin

2003-03-28

4.13 Purity

Test patterns : Full white / Red / Green / Blue.

Conditions : As stated in item 4.0, the purity must be checked under

specific

destinations of earth magnetic environments and the monitor

must be well degaussed.

After warming-up time of 30 min., no color stains may occur in the above

four patterns.

4.14 Moir

Condition: Display a full white pattern. At any preset mode ,

the display size must be set as Fig.1.

The moir area should be < 1/3 area of the screen with

luminance setting from 15 to 33 FL.

4.15 Blemish

Blemish shall be in accordance with CRT specification.

5.0

Mechanical characteristics

5.1

User controls

- Power ON/OFF key

- LightFrame key

- 3 Key digital user control (OSD)

5.2

Connectors and cables

5.2.1 Power cord type : 3 leads plugable power cord

with protective earthed plug or IBM Hooded

Length

: 1.5 m

50 mm (excluding connector)

Safety requirements : See following.

Approval

Countries

Mains plug Wire

Connector

Germany

VDE

Switzerland

SVE

Belgium

CEBEC

Sweden

SEMKO

SEMKO SEMKO

Finland

Norway

NEMKO

NEMKO --

Denmark

DEMKO

DEMKO DEMKO

Italy

OVE

Netherlands KEMA

KEMA

U.K.

ASTA

HAR

ASTA

U.S.A.

http://jdwxzlw.5d6d.com/?fromuser=华盛维修

家电维修资料网，免费下载各种维修资料

Summary of Contents for 107B50/74












































































Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands

Philips 107B50/74, Service Manual

Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands