Philips 107B50/74 Service Manual Download Page 17

Page: 17 / 75

DDC Instructions (Continued)

Go to cover page

V30 107B5

Fig. 16

Fig. 18

Step 8: Save DDC data

Sometimes, you may need to save DDC data as a text file for using

in other IC chip. To save DDC data, follow the steps below:

1. Click

(Save) icon (or click "file"-> "save as") from the tool bar

and give a file name as shown in Fig. 19.

The file type is EDID301 file (*.ddc) which can be open in WordPad.

By using WordPad, the texts of DDC data & table (128 bytes, hex

code) can be modified. If DDC TEXTS & HEX Table are completely

correct, it can be saved as .ddc flie to re-load it into EEPROM for

DDC Data application.

Step 5: **Configuration Setup & Enter Factory Mode **

for "write EDID data"

1. Click

icon from the tool bar to bring up the Configuration Setup

windows again. Then, select "Software DDC only" as shown in

Fig. 16. Click "OK".

Step 6: Write DDC data

1. Click

(Write EDID) icon from the tool bar to write DDC data.

Bring up "Writing 0%~100%, ready" a progressing bar on the left

down corner.

2. Click

(Read EDID) to confirm it.

Step 7: Confirm Serial Number in User Mode

. Press the

button to turn off the monitor. Press the

button

again to turn on the monitor.

2. Press the

button to bring up the OSD Main Menu.

3. Press the

button to select Extra Controls, press the

button to confirm your selection.

4. Confirm the Serial Number "123456" is updated

as shown in Fig. 18.

Fig. 19

If you do not select "Software DDC only", when you execute

"write EDID", it will bring up an error message as below.

If you do not access "Factory mode", when you execute

"write EDID", it will bring up an error message as below.

To access factory mode

1. Turn off monitor (don't turn off PC)

2. Press "

" and "

" simultaneously on the front control

panel,then press "

",wait till the OSD menu with characters

V20 107E5 V0.20 20021217 (below OSD menu)" come on the

screen of monitor.

If OSD menu disappears on the screen of monitor, press "

again (anytime), then the OSD menu comes on the screen again.

Fig. 17

MODEL SELECT

V30 107B5 P V0.51 20021220

Factory

Mode

Indicator

2. Click

Save

107B5 V30

http://jdwxzlw.5d6d.com/?fromuser=华盛维修

家电维修资料网，免费下载各种维修资料

Summary of Contents for 107B50/74












































































Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands

Philips 107B50/74, Service Manual

Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands