Philips 107B50/74 Service Manual Download Page 59

Page: 59 / 75

V30 107B5

GENERAL PRODUCT SPECIFICATION

17" V30 GS4 107B5-86K CMTR

TYPE

: 107B50/74

BRAND : PHILIPS

8639 000 14235

2003-03-28

590

Go to cover page

Wayne Lin

2003-03-28

Implosion protection

: By P-Mini-rim-band.

EHT

: 25.0

1 KV (Ib=0)

Visible screen area

: 325.2 mm x 243.8 mm

CRT Source

: CPT, LG, SDI

3.6

RGB Amplifier

3.6.1 Video amplifiers

Dot Rate

: 176 MHz

Over / undershoot

: 15% Max. (Transient response)

Sag

: 5% Max. (pulses of 0.70H)

Black level shift

: 5% Max.

3.6.2 Brightness and Contrast

Reference mode 68.7 KHZ/85 HZ full white pattern.

DISPLAY LIGHT OUTPUT

Light output

Brightness Contrast

(full white)

Minimum Minimum

not visible

Center

Maximum

5 FL.

80mmx80mm block

Brightness at 50% and contrast at 100% light output is 43+/-5 FL.

sRGB : When sRGB mode is selected, the light output (Full white pattern)

shall be 23 +/-

3FL regardless of user contrast and brightness controls. Adjusting user

contrast or

brightness control will make the monitor auto-exit sRGB mode and go to

6500K mode.

3.6.3 Raster light output

Apply 68.7KHz/85Hz mode with no video pattern, set brightness at

center(50%) and contrast control at minimum(0%).

The light output on the screen center should be < 0.15FL.

3.7 Variation of image size ( For preset modes only. Allow 30 minutes warm-up. )

Due to brightness change :

1.0 %

Long term (Static)

: <1.50mm on left/right side

(See Fig.7)

<1.20mm on top/bottom side

Due to aging

(25

C, 300 hrs)

1.0 %

Due to mains voltage

variation (

10% )

1.0 %

http://jdwxzlw.5d6d.com/?fromuser=华盛维修

家电维修资料网，免费下载各种维修资料

Summary of Contents for 107B50/74












































































Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands

Philips 107B50/74, Service Manual

Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands