Philips 107B50/74 Service Manual Download Page 12

Page: 12 / 75

Electrical Adjustments (Continued)

Go to cover page

V30 107B5

BIAS R G B : R(red) G(green) B(blue) cutoff

GAIN R G B : R(red) G(green) B(blue) gain

OSD contrast : OSD window contrast

V OFFSET : Vertical raster center

V GAIN

: Vertical size center

VLIN BAL : Vertical Linearity Balance

V FOCUS : Vertical Focus adiustment

T CORNER: Corner Correctionof TOP

B CORNER: Corner Correctionof BOTTOM

EHT H

: Horizontal Size compensation

EHT V

: Vertical Size compensation

Pincor T : Top corner asymmetry correction

Pincor B :Bottom corner asymmetry correction

Pincor S : Pincushion S-correction

Pincor W : Pincushion W-correction

B+ : High voltage adjustment

ABL

: Auto brightness Limitation

SUB

: Sub Contrast allowance range

SUB

: Sub Brigntness allowance range

SUB

: Horizontal size range adjustment range

HLIN

: Horizontal Linearity

V LIN

: Vertical Linearity

RANGE

: Zoom range

RANGE

: User Horizontal size adjustment range

7.2 Connect the video input, set brightness control at center, and

contrast control at maximum

7.3

set R,G,B cut-off at 127 9300k and 6500K(EEPROM preload value)

R,G,B gain at 185 9300k and

180 6500K(EEPROM preload value)

ABL

at 160 9300k (EEPROM preload value)

SUB-CON at 220 9300k (EEPROM preload value)

7.4 Adjust 9300K color:

With color analyzer CA 100,

set R,G,B cut-off x=0.283, y=0.297, Y=0.10

7.5 Set R,G,B gain Y= 41+/- 1FL, x=0.283, y=0.297

7.6 Repeat 7.4,7.5 until RGB three guns get x=0.283, y=0.297,

readings on low Y=0.10+/-0.05FL and high Y=41+/-1FL

brightness of 9300.

7.7 Adjust 6500K color:

With color analyzer CA 100,

set R,G,B cut-off x=0.313, y=0.329, Y=0.10

7.8 Set R,G,B gain Y= 36+/- 1FL, x=0.313, y=0.329

7.9 Repeat 7.7,7.8 until RGB three guns get x=0.313, y=0.329,

readings on low Y=0.10+/-0.05FL and high Y=36+/-1FL

brightness of 6500.

7.10 Adjust SUB-CON to get Y=41+/-1FL.

7.11 Apply full white pattern of 9300 mode, adjust ABL to reach

30 +/- 1FL(at 9300 high brightness of R/G/B gain,

contrast at 100%)

(for ref. 152,173,133,216,188,194)

(for ref. 158,177,136,208,148,132)

(for ref. 161,178,137,182,132,118)

(for ref. 127,255,190)

(for ref. 125,126,110,138)

(for ref. 140,130,58,170)

(for ref. 220,160,0,80,50)

(for ref. 75,55,104,203)

(for ref. 110,118,140,100)

(for ref. 255)

(for ref. 3,3)

Fig. 2.2

(for example: 152 is value of "BIAS R")

7. Alignment of Vg2 cut-off point, white tracking

Equipment : 1. Video Test Generator-801GC (Quantum Data)

2. Color-analyzer (Minolta CA-100)

VG2 [(screen), at the bottom of the L.O.T.].

7.1 Apply a video signal in the 1024 x 768 with 68.7 kHz/85 Hz mode,

select the "full white pattern" (sizes 306 x 230 mm).

* Use color-analyzer (Minolta CA-100) to adjust R/G/B cutoff and

gain.

OSD R/G/B cut-off and R/G/B gain can be accessed (for Philips

CRT), with initial data:

9300 K

R cutoff = 50%, R gain = 73% (I C)

G cutoff = 50%, G gain = 73% (I C)

B cutoff = 50%, B gain = 73% (I C)

6500 K

R cutoff = 50%, R gain = 71% (I C)

G cutoff = 50%, G gain = 71% (I C)

B cutoff = 50%, B gain = 71% (I C)

Brightness = 50%, Sub-Contrast = 86%, ABL = 63% (I C)

Step 1: To access factory mode

- Turn off monitor (don't turn off PC)

- Press "

" and "

" simultaneously on the front control

panel,then press "

",wait till the OSD menu with characters

V30 107B5 P V0.51 20021220 (below OSD menu)" comes on the

screen of monitor as shown in Fig. 2.1.

- If OSD menu disappears on the screen of monitor, press "

again (anytime), then the OSD menu comes on the screen again.

- Using "

" to select

- Using "

" : to increase or decrease the value.

M 32 107E/T4P V1.23 20020426

- Press "

" button to access/confirm the selection.

Bring up the "function adjustment" as shown in Fig. 2.2.

- Press '"

" button for function selection as shown in

Fig. 2.2.

- Press "

" button to access/confirm each item selection

(The cursor indicator will be changed from yellow colour to

red colour.)

MODEL SELECT

Factory

Mode

Indicator

Fig. 2.1

9300 BIAS R G B

GAIN R G B

6500 BIAS R G B

GAIN R G B

SRGB BIAS R G B

GAIN R G B

SRGB (

)

CORNER(T B) PINCOR(T B )

PINCORR(S W) V (OFF GAIN)

SUB (

) LIN ( H V)

RANGE ( USERH

) B+ ABL

EHT ( H V ) V(LINBAL FOCUS)

OSD

LF(BRIGH SHARP)

EXIT

152

V30 107B5 P V0.51 20021220

http://jdwxzlw.5d6d.com/?fromuser=华盛维修

家电维修资料网，免费下载各种维修资料

Summary of Contents for 107B50/74












































































Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands

Philips 107B50/74, Service Manual

Search results

Summary of Contents for 107B50/74

Reviews:

Related manuals for 107B50/74

Brands by name

Popular brands