manualshive.com logo in svg

Pentair raychem ngc-30/uit2, Programming Manual

Share
Download
Pentair raychem ngc-30/uit2 Programming Manual Download Page 69

69 / 84

industrial heat tracing solutions

EN-RaychemNGC30UIT2Programming-AR-H58186      02/16

seCtion 4 – aPPendiCes

Qualified Pentair Industrial Heat Tracing Solutions Personnel Only. It is recommended that only
Pentair Industrial Heat Tracing Solutions personnel exit the NGC-UIT2 program.

aPPendiX a. nGC-uit2 soFtWare uPGrade ProCess

The NGC-30 UIT2 Software can be upgraded using a memory stick and the USB Port on the NGC-UIT2. 

step 1 

–  Copy the entire folder labeled "Setup", where the new NGC software version is saved, to the 

USB memory stick.

step 2

–  Insert the USB flash drive with the new software into the USB port on the NGC-UIT2 Unit.

step 3 (For uit/uit2 software version 1.17.35 and higher)

–  The UIT/UIT2 Software versions 1.17.35 and higher do not require power cycle. The NGC-

UIT/UIT2 can recognize the USB stick with or without power cycling.

  While NGC-UIT2 Program is running, insert the USB flash drive with the new software 

version into the USB Port on the Unit Wait approxi-mately one minute until the program 

displays the selection screen. This screen will indicate four options, as shown below:

Fig. A.1   Window to select  UIT2 software upgrade or mass configuration

step 4

–  Choose the Update NGC-UIT2 from USB Drive option by pressing that button on the screen. 

step 5

–  The program will prompt you to confirm whether overwrite the current program is 

acceptable, See below. Press "Yes" button.

WARNING:

Summary of Contents for raychem ngc-30/uit2





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands