Pentair Hydromatic Installation And Service Manual Download Page 2

2

personnel capable of using 

reasonable engineering principles 

for the installation and operation 

of the system.

Excavation 

Instructions

Excavation location shall be 

made according to local codes 

and regulations. Check with 

local utility companies for 

 

the location of underground 

utilities prior to excavation. 

Care should be taken to avoid 

buried utility lines, piping, and 

other buried structures and 

foundations. Failure to follow 

these instructions may result  

in serious personal injury or 

death.
Excavation for Basin Systems

Effect appropriate excavation 

based on size of the basin, desired 

entrance point of the influent line, 

and entrance of power connection.

General 

Information

Thank you for purchasing your 

Low Pressure Sewer Basin 

System.
Before Installation:

This manual contains important 

information for the safe use of 

this product. Read this manual 

completely and follow the 

instructions carefully. Reasonable 

care and safe methods relating 

to the installation and operation 

of this product should be 

practiced. Check local codes and 

requirements before installation.

Risk of electrical shock or 

electrocution. May result 

in serious injury or death or  

fire hazard. Installer must 

disconnect all electrical sources 

prior to installation. Only 

qualified personnel may install 

this system. NFPA 70/National 

Electric Code (NEC) or local 

codes must be followed. System 

must be properly grounded 

according to NEC.

Biohazard risk. Once the 

wastewater source has been 

connected to system, biohazard 

risk exists. Installer(s) and/

or service personnel must use 

proper Personal Protective 

Equipment and follow handling 

procedures per OSHA 29 CFR 

1910.1030 when handling 

equipment after wastewater 

source has been connected to 

the system.

Risk of fire or explosion. Do 

not smoke or use open flames 

in or around this system. This 

system is not intended for use in 

hazardous locations per NFPA 

70 National Electric Code. 

Consult factory for optional 

equipment rated for this use.

Cutting risk. Risk of serious 

cutting or amputation exists. 

Disconnect all power sources 

prior to servicing pump or 

grinding mechanism. Pump may 

start without warning. Grinding 

mechanism is extremely sharp. 

Use caution when handling 

grinder mechanism.
CALIFORNIA PROPOSITION 

65 WARNING:

  This product and 

related accessories contain 

chemicals known to the State of 

California to cause cancer, birth 

defects or other reproductive 

harm.
DO NOT THROW AWAY OR 

LOSE THIS MANUAL. Keep 

it in a safe place so that you may 

refer to it often for the continued 

safe operation of the product.

Installation Skill 

Requirements

The installation of a basin system  

is a specialized skill, which 

requires individuals with the basic 

understanding of excavating, pipe 

fitting, and electrical wiring. 
These instructions are meant 

only to be an installation guide; 

therefore, unusual installation 

conditions not covered in these 

instructions require experienced 

Summary of Contents for Hydromatic













Reviews: