Demo Kiosk Technical Support
For questions about the demo kiosk set up or for
additional copies of this manual, please use the follow-
ing contact information:
Thermal Solutions, Inc.
1074 Classic Drive
Apex, NC 27539
Phone: (919) 362-4575 (8 A.M. to 5 P.M. ET)
Email: [email protected]
Software downloads available at:
http://www.thermal-solutions.com/customerdata/pentair/
PumpDaqSetupUS/.
Go to page 11 for instructions on how to install the
latest software version.
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
Attention Installer:
This manual contains important information about the installation, operation and safe use of this
product. This information should be given to the owner and/or operator of this equipment. Additional copies of this manual
are available at:
http://www.thermal-solutions.com/customerdata/pentair/Kiosk%20Instructions
/
Before installing this product, read and follow all warning notices and instructions which are included. Failure to follow safety
warnings and instructions can result in severe injury, death, or property damage. When installing and using this electrical
equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Technical Support for IntelliFlo
®
Operation
If you have questions about Pentair Water Pool and Spa
(“Pentair”) IntelliFlo
®
pump operation, please use the following
contact information:
Sanford, North Carolina
(8 A.M. to 5 P.M. ET)
Phone: (919) 566-8000
Fax: (919) 566-8920
Moorpark, California
(8 A.M. to 5 P.M. PT)
Phone: (805) 553-5000 (Ext. 5591)
Fax: (805) 553-5515
Web site:
visit www.pentairpool.com or www.staritepool.com
Pump Demo Manual Rev. A2 2/29/12
© 2012 Pentair Water Pool and Spa, Inc. All rights reserved.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000
This document is subject to change without notice.
IntelliFlo
®
and Pentair Water Pool and Spa
®
are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. and/or its
affi liated companies in the United States and/or other countries. Unless noted, names and brands of others that may be used in this
document are not used to indicate an affi liation or endorsement between the proprietors of these names and brands and Pentair Water
Pool and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those parties or others.
Always disconnect power to the pump at the circuit breaker and disconnect the communication cable before
servicing the pump. Failure to do so could result in death or serious injury to service people, users or others
due to electric shock. Read all servicing instructions before working on the pump.
To reduce the risk of injury, service should only be performed by a qualifi ed service professional.
To reduce the risk of injury, do not permit children to use this product.
DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the
strainer pot. Pumps operated in these circumstances may experience a buildup of vapor pressure and
may contain scalding hot water. Opening the pump may cause serious personal injury. In order to avoid
the possibility of personal injury, make sure the suction and discharge valves are open and strainer pot
temperature is cool to touch, then open with extreme caution
IMPORTANT! READ BEFORE TURNING ON THE PUMP
The pump can draw up to 3000 watts of power during priming and start up (typical 120V 20 Amp circuit is limited
to 1800 watts maximum). Check to be sure the pump watt and power usage does not exceed the rated capacity of
the electrical outlet.
For continued, safe operation,
set the pump’s maximum speed prior to operation. The pump should not run
on a high speed for an extended length of time.
Refer to the IntelliFlo
®
installation and user’s guide for
instructions on how to set the pump’s maximum speed.
