Pentagram Cerberus Wi-Fi Lite Installation And User Manual Download Page 7

Page: 7 / 64

Cerberus Wi-Fi Lite (P6381-0)

Back Panel

Label

Used for...

1-4 (RJ-45)

Connecting to computers/devices using the Ethernet cable

WAN (RJ-45)

Connecting to a cable/DSL modem using the Ethernet cable

RESET

Resetting the device.

PWR

Connecting with supplied power adapter (9V 0,8A)

Default Settings

Before changing configuration familiarize yourself with these default settings.

IP Address

192.168.1.254

Subnet Mask

255. 255. 255.0

SSID

Wireless-G Router

DHCP Server

Enabled

DHCP Server IP Address Pool

100 IP addresses
from 192.168.1.100

IP Address Lease Time

86400 seconds (24 hours)

User Name

root

Password

1234

It is recommended to change default password as soon as possible.
If you ever forget the password to log in, you may need to reset router to restore the factory
default settings. This procedure is described on the next page.

Summary of Contents for Cerberus Wi-Fi Lite

































































Search results

Summary of Contents for Cerberus Wi-Fi Lite

Reviews:

Related manuals for Cerberus Wi-Fi Lite

Brands by name

Popular brands

Pentagram Cerberus Wi-Fi Lite, Installation And User Manual

Search results

Summary of Contents for Cerberus Wi-Fi Lite

Reviews:

Related manuals for Cerberus Wi-Fi Lite

Brands by name

Popular brands