PDL D3-2.5, Instruction Manual, Page: 46 / 113

Microdrive Series Instruction Manual
4201-109 Rev I
46
MULTIFUNCTION INPUT MODES (SCREEN 66)
NO. NAME CONTROL INPUTS
IP1
IP2 IP3 IP4 IP5
T 8 T 9 T 10 T 11 T 12
0 COMMISSION DISABLED DISABLED DISABLED DISABLED DISABLED
1 STANDARD (3 WIRE) STOP START STOP/RST DIRN INV EMERG STOP
2 2 WIRE & STOP/RESET STP/STR COMMS. STOP/RST DIRN INV EMERG STOP
3 2 WIRE & START/RESET STP/STR COMMS. STRT/RST DIRN INV EMERG STOP
4 3 WIRE DIRECTION STOP START+ STOP/RST START– EMERG STOP
5 MULTISPEED X Y STOP/RST Z EMERG STOP
6 SWITCH SPEED U V STP/STR DIRN INV EMERG STOP
7 INCH STANDARD STOP START STOP/RST DIRN INV INCH1
8 DUAL INCH STD STOP START STOP/RST INCH2 INCH1
9 INCH LATCHED STOP START STOP/RST INCH2 INCH1
10 INCH STD & E/STOP STP/STR INCH1 STOP/RST DIRN INV EMERG STOP
11 DUAL INCH & E/STOP STP/STR INCH1 STOP/RST INCH2 EMERG STOP
12 INCH 2 WIRE & DIR STP/STR INCH2 STOP/RST DIRN INV INCH1
13 INCH 2 WIRE,RST,E/STOP INCH1 INCH2 STRT/RST DIRN INV EMERG STOP
14 CRANE 1 + TRAVEL –TRAVEL HOLD +SLOW –SLOW
15 CRANE 2 STRT/RST DIRN INV WKG LIMIT +SLOW –SLOW
16 DUAL ACC/DEC ALT ACC/DEC START STOP/RST DIRN INV INCH 1
17 MOTORISED POT RED. REF INC. REF STOP/RST DIRN INV START
18 CRANE 3 +HOLD –HOLD ADJUST +SLOW –SLOW
Table 2.1.2 Display Screen Messages - Full Menu Modes
OUTPUT RELAY MODES (SCREENS 67, 68, 69)
NO. NAME OPEN STATE CLOSED STATE NOTES
(NORMALLY OPEN CONTACT)
0 FAILSAFE FAULT FAULT NO FAULT
1 START NOT STARTED STARTED
2 RUN NOT RUNNING RUNNING
3 START OR RUN NOT START OR RUN START OR RUN
4 INVERTER OVERLOAD NOT OVERLOADED OVERLOADED
5 MOTOR O/L NOT OVERLOADED OVERLOADED
6 FREQ SENSE BELOW Fr OFF ABOVE Fr ON SCREENS 29/30
7 CURRENT SENSE BELOW SENSE I ABOVE SENSE I SCREEN 31
8 INVERTER DIRECTION FORWARD REVERSE
9 COMMS OUTPUT NOT SET SET
10 AT SET FREQ NOT AT FREQUENCY AT FREQUENCY
11 O/L ALARM NOT OVERLOADED MOTOR OR INVERTER OVERLOADED
12 POWER FLOW MOTORING REGENERATING
13 FEEDBACK SENSE FB ABOVE REFERENCE FB BELOW REFERENCE SCREEN 54
ANALOGUE OUTPUT MODES (SCREEN 70)
CODE DESCRIPTION0-10Vdc=
00 OUTPUT FREQUENCY 1 0-100Hz
01 OUTPUT FREQUENCY 2 0-200Hz
02 OUTPUT CURRENT 0-150% OF DRIVE RATED CURRENT
03 OUTPUT VOLTAGE 0-500Vac
04 COMMUNICATION OUTPUT 0-10Vdc
05 TORQUE CURRENT 0-150% OF DRIVE RATED CURRENT
06 MOTOR POWER 0-150% OF MOTOR RATED POWER
MODULATION FREQUENCY (SCREEN 72)
CODE DESCRIPTION
NB NARROW BAND 4kHz
WW WHISPER WAVE 4kHz AVERAGE
NL NARROW BAND 2kHz
WL WHISPER WAVE 2kHz AVERAGE
CURRENT LIMIT SOURCE (SCREEN 76)
CODE CONTROL SOURCE
00 INTERNAL ADJUSTMENT SCREEN 18
01 0-10V ANALOGUE 0 TO 10 Vdc
02 4-20mA ANALOGUE 4 TO 20 mA