Parsun F50 BEL-D Owner'S Manual Download Page 35 | Manualshive

Page: 35 / 69

background image

28

For electric tilt model:
Press the “UP” switch to tilt the outboard motor up to the highest position, and push in the tilt support
lever.

2.11.2 Tilting down

1. Place the tilt lock lever (if equipped) in the up position.

2. Hold the rear of the top cowling , tilt the engine up slightly and return the tilt support lever.

3.Slowly tilt the outboard motor down. place the tilt lock lever in the down position

For electric tilt model:
Pull out the tilt support lever, press the “DN” switch to tilt the outboard motor down to the lowest
position..

DN

UP

DN

UP

«
...
33
34
35
36
37
...
»

Summary of Contents for F50 BEL-D






































































Reviews:

No comments

Related manuals for F50 BEL-D

Brand: E-peas Pages: 2

Brand: Yamaha Pages: 82

Brand: ECS Pages: 72

Z690 Phantom Gaming 4

Brand: ASROCK Pages: 109

Brand: Biostar Pages: 85

Brand: NXP Semiconductors Pages: 269

Brand: ASROCK Pages: 6

Brand: Energy Pages: 14

Brand: Mercury Pages: 102

Qseven conga-QA5

Brand: Congatec Pages: 61

Brand: Biostar Pages: 210

Brand: Ublox Pages: 32

Brand: IEI Technology Pages: 53

Brand: Texas Instruments Pages: 24

Brand: TYAN Pages: 74

Brand: Fujitsu Pages: 30

Brand: Maxtang Pages: 14

Brand: Supermicro Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands