Parsun F50 BEL-D Owner'S Manual Download Page 50 | Manualshive

Page: 50 / 69

background image

43

5. Replace the gasket with a new one. Reinstall the fuel joint assembly and tighten the screws firmly.

3.11 Checking and replacing anode(s)

Inspect the external anodes periodically. Remove scales from the surfaces of the anodes. Consult your
dealer for replacement of external anodes.

CAUTION:

3.12 Checking top cowling

Do not paint anodes, as this would
render them ineffective and can
cause

more

rapid

engine

corrosion.

Check the fitting of the top cowling by
pushing it with both hands. If it is
loose have it repaired by your dealer.

«
...
48
49
50
51
52
...
»

Summary of Contents for F50 BEL-D






































































Reviews:

No comments

Related manuals for F50 BEL-D

Brand: Lantronix Pages: 17

Brand: Biostar Pages: 61

Brand: Biostar Pages: 53

Brand: Safran Pages: 26

phyBOARD-Subra-i.MX6

Brand: Phytec Pages: 2

Z270 Gaming Pro Carbon Motherboard

Brand: MSI Pages: 92

Brand: QDI Pages: 85

Brand: DFI Pages: 67

Brand: AMPTRON Pages: 16

Brand: DFI Pages: 60

Brand: Icop Pages: 40

Brand: JETWAY Pages: 44

SUPER P4DPL-8GM

Brand: Supero Pages: 86

Brand: Gigabyte Pages: 70

Brand: BESTEK Pages: 13

Brand: Linear Technology Pages: 6

Brand: EVGA Pages: 40

Brand: Supermicro Pages: 121

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands