![background image](http://html1.mh-extra.com/html/parkside/stapler/stapler_operation-and-safety-notes_4178071007.webp)
7
GB
sound level while working may exceed 98.7 dB (A).
These values are device-related values and do not
represent the generation of noise at the place of use.
The noise generated at the place of use depends
e.g. on the working environment, workpiece, work-
piece support, the number of tack driving cycles.
Depending on the workplace conditions and the
shape of the workpiece, it may be possible to take
job-specific noise reduction measures, such as plac-
ing the workpiece on a sound-damping substrate,
covering or clamping the workpiece to prevent vi-
bration, setting the pressure to the lowest possible
value adequate for the job. In some cases, it may
be necessary to wear ear protection.
Wear ear protection!
Total vibration in accordance with EN ISO 8662-11:
Vibration emission value a
h,D
= 2.0 m / s
2
Uncertainty K = 1.5 m / s
2
Mechanical impact (vibration)
The vibration values for the fastener driving tool
were calculated in accordance with ISO 8662-
11:1999 — Hand-held portable power tools —
Measurement of vibrations at the handle — Fasten-
er driving tools (see Technical data). The value is a
device-related value and does not represent the
effect on the hand-arm system of using the device.
The effect on the hand-arm system of using the de-
vice depends e.g. on the tightness of your grip on
the handle, contact pressure, direction of working,
set working air pressure, workpiece, workpiece
support.
Fastener driving
tool safety
WArNINg!
read all the safety
advice and instructions.
Failure to observe
the safety advice and instructions could result in se-
rious injury and/or damage to property.
Keep all the safety advice and instruc-
tions in a safe place for future
reference.
J
Before you start work with the
device, check that its safety features
and trigger fittings are working
properly and that all screws, bolts
and nuts are fixed tightly in place.
J
Do not carry out unauthorised ad-
justments or modifications to the
fastener driving tool.
J
Never disassemble or block any part
of the fastener driving tool, such as
the trigger lock.
J
Do not carry out any “emergency
repairs” using unsuitable means.
J
The fastener driving tool must be
regularly and properly maintained
in accordance with the manufactur-
er’s instructions.
J
Do not risk weakening or damaging
the device by e.g.:
- subjecting it to impact or engraving it,
- converting it in a manner not
approved by the manufacturer,
- using templates that are made from
a hard material, e.g. steel,
- allowing it to fall or pushing it over
the floor,
- using it like a hammer, or
- using it to apply any kind of force.
Q
Safety at work
J
Never point a fastener driving tool
that is ready for use directly towards
yourself or another person.
J
When working, hold the fastener
driving tool in such a way that your
head and body cannot be injured
should kickback occur as a result of
an interruption of the energy supply
or striking a hard spot in the workpiece.
J
Never trigger the fastener driving
tool into open space.
Otherwise you risk
injury from flying fasteners and/or overloading
the device.
J
Disconnect the fastener driving tool
from the air pressure network before
carrying it to a different location, es-
Introduction / Fastener driving tool safety
32999_Druckluft-Tacker_Content_LB4 (ohne PL-HU).indd 7
06.07.09 09:51
Summary of Contents for STAPLER
