![background image](http://html1.mh-extra.com/html/parkside/stapler/stapler_operation-and-safety-notes_4178071010.webp)
10 GB
NOTE:
Fine adjustment can also be done using
the knurled screw
9
.
j
Turn the knurled screw
9
in the direction of
the lower stop
8
in order to sink the fastener
more deeply into the work piece.
j
Turned the knurled screw
9
in the direction of
the upper stop
10
in order to sink the fastener
less deeply into the work piece.
NOTE:
The compressed air tacker can be used on
a horizontal or on a vertical workpiece.
j
Turn the exhaust cover
1
to direct the escap-
ing air in the desired direction.
j
After you finish work, disconnect the device
from the compressor.
NOTE:
First disconnect the hose from the
compressor and only then disconnect the
compressed air supply hose from the device.
This will ensure that the compressed air supply
hose does not wave around in an uncontrolled
manner.
Q
Maintenance and cleaning
J
DANgEr OF BUrNS!
Do not start any
cleaning or maintenance work on the com-
pressed air tacker until it has completely
cooled down.
J
DANgEr OF INJUrY!
Always disconnect
the device from the compressed air source
before you clean or maintain it.
Q
Maintenance
j
Grease the device regularly. This will ensure
that it continues to work properly and has a
long service life.
Lubrication with the oil mist lubricator
NOTE:
As an air preparation stage downstream
of the pressure reducer, an oil mist lubricator pro-
vides a continuous, optimum level of lubrication to
the compressed air tacker. An oil mist lubricator
gives off fine droplets of oil into the air and thus
ensures controlled lubrication.
j
Install the oil mist lubricator downstream of the
(filter)/pressure reducer. To do this, insert the
plug-in nipple of the oil mist lubricator into the
quick-release coupling of the (filter)/pressure
reducer.
j
Then connect the compressed air device to the
quick-release coupling provided for it.
Manual lubrication
NOTE:
If you do not have an oil mist lubricator,
you must lubricate the device before each period
of use and/or after long periods of disuse.
j
Place 3 - 5 drops of compresses air special oil
into the threaded plug-in nipple
4
of the
compressed air tacker.
j
Then press the trigger
2
a few times.
j
Introduce 5 - 10 drops after a period of
disuse of more than 5 days.
Q
Cleaning
J
Do not use sharp objects for cleaning the
device. Do not allow any liquids to enter the
device. Otherwise the device could be damaged.
j
Clean the device frequently; for best results, do
this immediately after you have finished using it.
j
Use a dry cloth to clean the housing – under
no circumstances use petrol, solvents or clean-
ing agents that attack plastic.
j
Pack away the compressed air tacker in the
supplied carrying case after each use to
protect it from dirt.
Q
Service
J
WArNINg!
Have your fastener
driving tool repaired only by qualified
specialist personnel using original
manufacturer parts only.
This will ensure
that your fastener driving tool remains safe to use.
Q
Warranty
This appliance is guaranteed for 3 years
from the date of purchase. It has been care-
Operation / Maintenance and cleaning / Service / Warranty
32999_Druckluft-Tacker_Content_LB4 (ohne PL-HU).indd 10
06.07.09 09:51
Summary of Contents for STAPLER
