manualshive.com logo in svg

Parker Hydraulics Hydraguide HGF Series, Service Procedure, Page: 37 / 46

Share
Download
Parker Hydraulics Hydraguide HGF Series Service Procedure Download Page 37

HGF Series Service Procedure

30

Figure 82

Figure 81

Figure 80

Figure 79

Install alignment pins

29. Place two alignment pins (11) into 

the metering ring (17). See 
FIGURE 79.

Install isolation
manifold

30. Stack the isolation manifold (15) (4 

plates bonded together) onto the 
metering ring (17), aligning the 
grooves on the side of the 
manifold with the grooves on the 
side of the upper cover plate (32) 
and the alignment pin holes with 
the alignment pins in the metering 
ring. The isolation manifold 
surface without the recessed slots 
must be placed toward the 
metering ring. See FIGURE 80.

Install two alignment
pins

31. Install two alignment pins (11) into 

the isolation manifold (15). See 
FIGURE 81.

Install 1/2 inch springs

32. Place the three 1/2 inch (13 mm) 

springs (14) into the spring 
pockets of the isolation manifold 
(15). See FIGURE 82.

NOTE

NOTE: Two different length springs
are used in the unit. Be sure to use
the 1/2 inch (13 mm) length springs
(14) during this part of the assembly.

Summary of Contents for Hydraguide HGF Series















































Reviews:

No comments