Parker Hydraulics Hydraguide HGF Series Service Procedure Download Page 20 | Manualshive

Page: 20 / 46

background image

13

HGF Series Service Procedure

Figure 17

Figure 16

Figure 15

Figure 14

16. Inspect the springs (14), for

bent or distorted coils. If a
spring is broken or deformed,
all six springs in the unit must
be replaced. See FIGURE 14.

Inspect springs

17. Remove hex drive assembly

(10) from drive link (16). See
FIGURE 15.

Remove hex drive
assembly

18. The pin in the hex drive

assembly (10) should not show
wear and must be firmly
pressed in place. The sides of
the hex and the slot should
not have grooves or scoring. If
the hex drive assembly (10)
shows signs of this type of
wear, it must be replaced.

Inspect hex drive
assembly

19. Remove the two alignment

pins (11) that align the port
manifold (8), valve ring (12)
and isolation manifold (15).
See FIGURE 16.

Remove alignment pins

NOTE: A service kit of nine
alignment pins (11) is available for
servicing the unit.

NOTE

20. Remove the isolation manifold

(15), (four plates bonded together).
See FIGURE 17.

Remove isolation
manifold

«
...
18
19
20
21
22
...
»

Summary of Contents for Hydraguide HGF Series















































Reviews:

No comments

Related manuals for Hydraguide HGF Series

Brand: Rangevision Pages: 31

Brand: Keithley Pages: 149

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: GE Pages: 154

Arize Element Top Light

Brand: GE Pages: 2

Brand: Datex-Ohmeda Pages: 104

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 166

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 340

Brand: GE Pages: 138

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: C.M.O Pages: 10

Brand: GE Pages: 698

WJHD100 - DIGITAL DISC RECORDE

Brand: Panasonic Pages: 7

Brand: Modulate Pages: 2

Brand: UFO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands