Parker Hydraulics Hydraguide HGF Series Service Procedure Download Page 33 | Manualshive

Page: 33 / 46

background image

26

HGF Series Service Procedure

Figure 66

Figure 65

Figure 64

Figure 63

16. Place commutator ring (21) either

side up on top of stator (25). Align
commutator ring screw recesses
with stator screw slots. See
FIGURE 63.

Install commutator ring

17. Place commutator cover (20) on

top of commutator ring (21) with
flat surface toward commutator.
Align screw holes in cover, with
screw holes in drive plate (26).

See FIGURE 64.

Install commutator
cover

18. Screw the eleven hex. socket

head cap screws (18) loosely into
metering package. See FIGURE 65.

Install cap screws

NOTE: The commutator ring (21)
must be concentric with drive plate
(26) within .005 inch (.127 mm) total
indicator reading after tightening the
eleven hex. socket head cap screws
(18). The next two procedures are a
method of achieving the concentricity.

NOTE

19. Place the metering ring (17) on a

hard flat surface. Place the
assembled metering package into
the metering ring with the
commutator cover (20) down, such
that the drive plate is partially out
of the metering ring. (A suitable
wood block under the metering
package will hold it in this
position.) See FIGURE 66.

Align commutator ring
concentrically with
drive plate

«
...
31
32
33
34
35
...
»

Summary of Contents for Hydraguide HGF Series















































Reviews:

No comments

Related manuals for Hydraguide HGF Series

Brand: Campden instruments Pages: 8

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brand: LAHTI PRO Pages: 20

Brand: LAHTI PRO Pages: 16

Brand: J&M Pages: 53

Brand: Qazqa Pages: 2

Brand: Panlux Pages: 2

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Ultraflex Pages: 3

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 86

Brand: Native Instruments Pages: 245

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

Brand: Vaisala Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands