Parker Hydraulics Hydraguide HGF Series Service Procedure Download Page 5 | Manualshive

Page: 5 / 46

background image

1

HGF Series Service Procedure

NOTE:

A NOTE provides key infor mation to make a procedure easier or quicker to
complete.

CAUTION:

A CAUTION refers to procedures that must be followed to avoid damaging the HGF
or other system components.

Disclaimer

This Service Manual has been prepared by Ross for reference and use by mechanics who have been trained to repair
and service steering components and systems on commercial and non-commercial vehicles. Ross has exercised
reasonable care and diligence to present accurate, clear and complete information and instructions regarding the
techniques and tools required for maintaining, repairing and servicing the complete line of Ross HGF "Hydraguide"
Hydrostatic Steering Units. However, despite the care and effort taken in preparing this general Service Manual, Ross
makes no warranties that (a) the Service Manual or any explanations, illustrations, information, techniques or tools
described herein are either accurate, complete or correct as applied to a specific HGF steering unit, or (b) any repairs
or service of a particular HGF steering unit will result in a properly functioning steering unit.

If inspection or testing reveals evidence of abnormal wear or damage to the HGF steering unit or if you encounter
circumstances not covered in the Manual, STOP–CONSULT THE VEHICLE MANUFACTURER'S SERVICE MANUAL AND
WARRANTY. DO NOT TRY TO REPAIR OR SERVICE AN HGF STEERING UNIT WHICH HAS BEEN DAMAGED OR
INCLUDES ANY PART THAT SHOWS EXCESSIVE WEAR UNLESS THE DAMAGED AND WORN PARTS ARE
REPLACED WITH ORIGINAL EQUIPMENT REPLACEMENT AND SERVICE PARTS AND THE UNIT IS RESTORED TO
ORIGINAL EQUIPMENT SPECIFICATIONS FOR THE HGF STEERING UNIT.

It is the responsibility of the mechanic performing the maintenance, repairs or service on a particular HGF steering
unit to (a) inspect the steering unit for abnormal wear and damage, (b) choose a repair procedure which will not
endanger his/her safety, the safety of others, the vehicle, or the safe operation of the vehicle, and (c) fully inspect and
test the HGF steering unit and the vehicle steering system to insure that the repair or service of the steering unit has
been properly performed and that the steering unit and system will function properly.

Definitions

WARNING:

A WARNING REFERS TO PROCEDURES THAT MUST BE FOLLOWED FOR THE
SAFETY OF THE VEHICLE DRIVER AND THE PERSON INSPECTING OR
REPAIRING THE HGF.

«
...
3
4
5
6
7
...
»

Summary of Contents for Hydraguide HGF Series















































Reviews:

No comments

Related manuals for Hydraguide HGF Series

Brand: MacDon Pages: 17

Brand: Olympus Pages: 50

Brand: VAHVA Pages: 19

Brand: York Fitness Pages: 34

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: Patty-O-Matic Pages: 28

Brand: Nemalux Pages: 6

Brand: OBDLink Pages: 2

Brand: National Instruments Pages: 10

Brand: Samson Pages: 2

Brand: RAMVAC Pages: 53

Brand: RAB Pages: 4

EPL-HB-150LED-RT-IBSC

Brand: Larson Electronics Pages: 2

Brand: Carbatec Pages: 29

Brand: Moxa Technologies Pages: 2

Brand: PurAthletics Pages: 2

Brand: Commercial Electric Pages: 2

Brand: Buki Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands