Parkeon Strada Transfert Evolution 2 Operation Manual Download Page 23

Page: 23 / 50

6 - Coin collection

Strada Transfert Evolution2 - Operation manual

23/50

Emptying the drawer:



Keep the locking lever pressed in
and pull the slide to slide the
drawer out of the coin box.



Pull the unjamming handle and
shake it vigorously in every
direction to make all the coins
drop into the canister.

Closing the coinbox:



Put the unjamming handle back in place.



Keep the locking lever pressed in

(1)

and push the slide forward

(2)

to close

the coinbox drawer.

IMPORTANT:



Lock the coinbox drawer by turning the collection key anticlockwise

(3)



Remember to remove the collection key from the drawer lock (4).

Closing the drawer

Locking the drawer

The once-only opening system is set. It will make it impossible to open the canister
once again.

D1792

Handle

Drawer

Latch

D1794

Latch

D1793

Ticket slots

Drawer

D4130

Unjamming

handle

Locking lever

D5723

(3)

(4)

D4131

(1)

(2)

Summary of Contents for Strada Transfert Evolution 2



















































Search results

Summary of Contents for Strada Transfert Evolution 2

Reviews:

Related manuals for Strada Transfert Evolution 2

Brands by name

Popular brands

Parkeon Strada Transfert Evolution 2, Operation Manual

Search results

Summary of Contents for Strada Transfert Evolution 2

Reviews:

Related manuals for Strada Transfert Evolution 2

Brands by name

Popular brands