Parkeon Strada Transfert Evolution 2 Operation Manual Download Page 46

Page: 46 / 50

10 - Warnings and failures

Strada Transfert Evolution2 - Operation manual

46/50

10.2

Red failure LED

A flashing red LED means that the terminal is out of service. Please contact the
technical department and provide the following information:



Failure code number;



Failure message (the list below contains the most common failures);



If possible, a test ticket.

Failure display:

You can view the

DIAGNOSIS

code in hexadecimal format of a warning or a failure

without opening the maintenance door.



To do so, press the (red)

Cancel

key and the (green)

key of the

function keypad or extended keyboard simultaneously.



Hold the

Cancel

key pressed down till the "Release change button"

message is displayed.



Place the cursor on the

Errors

function in the menu that is displayed by

pressing the

button as many times as required.



Press

Cancel

to select the function.

The terminal will display a list with 20 most recent fault and failure codes.

An alternative solution is to open the maintenance door and select programming
function number

with the keyboard.

Code

Failure message

Problem

Solution

4000

LOAD BATTERY

MEASUREMENT

The buffer battery voltage
is too low when idle.

Change the battery.

4001

LOAD BATTERY

MEASUREMENT

The buffer battery voltage
is too low when idle.

Change the battery.

4101

COINBOX FULL FAILURE

The coinbox cannot accept
any more coins.

Collect the coins.

4103

COLLECTION NOT ENDED

Collection door not
properly closed.

Check if the doors are
closed correctly.

4200

PRINTER FEED SYSTEM
FAILURE

Printer jammed or failed

Check printer operation.

4201

PRINTER CUTTING
SYSTEM FAILURE

Printer jammed or failed

Check printer operation.

4202

PRINTER FEED SENSOR
FAILURE

Printer jammed or failed

Check printer operation.

4203

PRINTER CUTTING
SENSOR FAILURE

Printer jammed or failed

Check printer operation.

4204

NO PAPER

IN PRINTER

No more tickets.

Change the ticket roll.

Summary of Contents for Strada Transfert Evolution 2



















































Search results

Summary of Contents for Strada Transfert Evolution 2

Reviews:

Related manuals for Strada Transfert Evolution 2

Brands by name

Popular brands

Parkeon Strada Transfert Evolution 2, Operation Manual

Search results

Summary of Contents for Strada Transfert Evolution 2

Reviews:

Related manuals for Strada Transfert Evolution 2

Brands by name

Popular brands