Paradyne 7110 User Manual Download Page 136

Page: 136 / 167

MIB Descriptions

C-25

7110-A2-GB20-00

June 1997

Table C-11.

General Port Table Objects (2 of 2)

Object, OID, Access

Setting/Contents

Description

rs232PortInSpeed
(rs232PortEntry 5 )

1.3.6.1.2.1.10.33.2.1.5
read-write

Contains the port’s input
speed in bits per second.

Supports the following speeds
for the:

Management port: 2400

4800

, 9600, 14,400,

19,200, 28,800, 38,400.

rs232PortOutSpeed
(rs232PortEntry 6 )

1.3.6.1.2.1.10.33.2.1.6
read-write

Contains the port’s output
speed in bits per second.

The rs232PortOutSpeed
object has the same values
as the rs232PortInSpeed
object.

Supports the following speeds
for the:

Management port: 2400

4800,

9600, 14,400,

19,200, 28,800, 38,400.

Terminal port: 2400, 4800,
9600,14,400, 19,200,
28,800, 38,400.

This speed is only valid when the port is configured for asynchronous operation.

The following are not supported:

rs232PortInFlowType

(rs232PortEntry 7 )

rs232PortOutFlowType

(rs232PortEntry 8 )

Summary of Contents for 7110


































































































































































Search results

Summary of Contents for 7110

Reviews:

Related manuals for 7110

Brands by name

Popular brands

Paradyne 7110, User Manual

Search results

Summary of Contents for 7110

Reviews:

Related manuals for 7110

Brands by name

Popular brands