Paradyne 7110 User Manual Download Page 114

Page: 114 / 167

MIB Descriptions

C-3

7110-A2-GB20-00

June 1997

MIB II Object Groups

System Group

System Group objects are fully supported by the unit.

Table C-1.

System Group Objects

Object, OID, Access

Description

Setting/Contents

sysDescr

( system 1)

1.3.6.1.2.1.1.1
read-only

Provides a full name and
version identification for the
system’s hardware and
software.

PARADYNE T1 DSU/CSU

;

Model: 7110-

xx-xxx;

S/W Release:

yy.yy.yy;

H/W CCA number:

zzzz-zzz;

Serial number:

sssssss

sysObjectID

( system 2)

1.3.6.1.2.1.1.2
read-only

Identifies the network
management subsystem.

1.3.6.1.4.1.1795.1.14.2.5.2.1

sysContact

(system 4)

1.3.6.1.2.1.1.4
read-write

Provides the textual
identification of the contact
person for this managed
unit.

ASCII character string, as set
by the user.

sysName

(system 5)

1.3.6.1.2.1.1.5
read-write

Provides an
administratively-assigned
name for this managed unit.

ASCII character string, as set
by the user.

sysLocation

(system 6)

1.3.6.1.2.1.1.6
read-write

Provides the physical location
for this managed unit.

ASCII character string, as set
by the user.

sysServices

( system 7)

1.3.6.1.2.1.1.7
read-only

Functionality supported:

physical (1 ) – Layer 1
functionality for all
interfaces.

datalink/subnetwork ( 2 )
– Layer 2 functionality

( SLIP/ PPP ) for all

management links.

internet ( 4 ) – Layer 3
functionality ( IP ) for all
management links.

end-to-end ( 8 ) – Layer 4
functionality ( TCP/ UDP )
for all management links.

Object is set to 1+2+4+8 (15).

The unit supports a 127-character string for this object. An error message is sent to
the NMS if an attempt is made to write (set) more than 127 characters.

Summary of Contents for 7110


































































































































































Search results

Summary of Contents for 7110

Reviews:

Related manuals for 7110

Brands by name

Popular brands

Paradyne 7110, User Manual

Search results

Summary of Contents for 7110

Reviews:

Related manuals for 7110

Brands by name

Popular brands