Paradyne 7110 User Manual Download Page 39 | Manualshive

Page: 39 / 167

background image

Monitoring the DSU/CSU

4-7

7110-A2-GB20-00

June 1997

Viewing Network Performance Statistics

Network performance statistics allow you to monitor the current status of the
network operations. Performance statistics can assist you in determining the
duration of specific conditions and provide a historical context for problem
detection and analysis.

When the network interface is configured for ESF framing, network performance
is continuously monitored and maintained in two sets of aggregate registers:

Carrier Network Interface Registers (Telco)

User Network Interface Registers (User)

These status registers, listed in Table 6-2, collect performance data for the
previous 24-hour period. Performance data is updated in 15-minute intervals.
After 15 minutes, the current interval is rolled over into a set of accumulator
registers that represent the previous 96 15-minute intervals for the register. An
interval total of how many of the 96 registers contain valid data is also kept, as
well as a 24-hour total for each accumulator register.

To view the Network Performance Statistics, follow this menu selection sequence:

Main Menu

→

Status

→

Network Performance Statistics

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

main/status/performance/network

Device Name: Model: 7110

NETWORK PERFORMANCE STATISTICS

Current Interval Timer ESF Error Events

Telco=438 User=437 Telco=0 User=0

–––ES–– ––UAS––

––SES––

––BES–– ––CSS–– –LOFC–– –Status–

Tel Usr

Tel Usr Tel

Usr

Tel Usr

Tel Usr

Tel Usr

(User)

Current Int: 000 000

000 000 000

000

000 000

000 000

000 000

YL

Interval 01: 000 000 000 000

000

000

000 000

000 000

000

000

none

Interval 02: 000 000

000 000 000

000

000 000

000 000

000 000

none

Interval 03: 000 000

000 000 000

000

000 000

000 000

000 000

none

Interval 04: 000 000 000 000

000

000

000 000

000 000

000

000

none

Interval 05: 000 000

000 000 000

000

000 000

000 000

000 000

none

Interval 06: 000 000

000 000 000

000

000 000

000 000

000 000

none

Interval 07: 000 000 000 000

000

000

000 000

000 000

000

000

none

Worst Interval:24

24

14

14

14

14

09

09

18

16

44

44

Tel Tot(valid 96):00001

00000

00001

00000

00000

00000

Usr Tot(valid 96):00000

00000

00000

00000

00000

00000

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Ctrl–a to return to Data Display, ESC for previous menu MainMenu Exit

Refresh PgDn PgUp ClrStats

Select: 01, 02, 03, 04, 05, 06, 07...

NOTE:

Network performance statistics are only available for those interfaces using
ESF framing. Verify that the Line Framing Format field on the Network
Interface screen is set to ESF.

«
...
37
38
39
40
41
...
»

Summary of Contents for 7110








































































































































































Reviews:

No comments

Related manuals for 7110

Brand: D-Link Pages: 37

Brand: cable matters Pages: 12

Brand: Linksys Pages: 2

Netkey 73-TMWBG-001

Brand: TwinMOS Pages: 25

Brand: Diamond Multimedia Pages: 14

Brand: Velleman Pages: 4

CS1001 - Single

Brand: BOB Pages: 19

Brand: Renesas Pages: 26

Brand: Jabra Pages: 3

Brand: Ruijie Networks Pages: 19

Brand: D-Link Pages: 23

Brand: Louroe Electronics Pages: 8

Brand: Amp’ed RF Technology Pages: 6

Brand: Belkin Pages: 13

F5D4076 - Gigabit Powerline HD Starter

Brand: Belkin Pages: 14

Brand: APLIC Pages: 24

Brand: Kinivo Pages: 20

Brand: Connect Tech Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands