Paradyne 3165 Operator'S Manual Download Page 187 | Manualshive

Page: 187 / 316

background image

C. Configuration Options

3160-A2-GB24-10

March 2001

C-21

ComEscapeSeq:
Next Edit Clear Prev

Carrier Communication Port Escape Sequence. Specifies the communication port’s
escape sequence. Once the external device connection has been established, either you
or the DSU/CSU can command the external device to disconnect. Before doing so, you
may need to send the escape sequence out to switch the external device into command
mode. The escape sequence is an ASCII text string and may be up to 20 characters in
length. If the escape sequence is NULL, no escape sequence is sent out.

Edit – Allows you to edit and/or display the escape sequence using the generic text string
entry screen.

Clear – Allows you to clear the escape sequence. The escape sequence is set to a null
string.

NOTES:

– This configuration option is available on carrier-mounted DSU/CSUs only.

▲

– This configuration option is not available if the ComExtDev configuration option is

set to AT or the communication port is disabled.

ComEscDel: None
Next None 0.2s 0.4s 0.6s 0.8s 1.0s Prev

Carrier Communication Port Escape Sequence Delay. Specifies the delay used while
sending the communication port escape sequence. Use the communication port escape
delay to specify the delay before sending the first character of the escape sequence and
the delay after the last character of the escape sequence. During the delay, no data is sent
out the communication port.

None – No communication port escape sequence delay.

X.Xs – The delay used during the communication port escape sequence (where X.X is
0.2, 0.4, 0.6, 0.8, or 1.0 seconds).

NOTES:

– This configuration option is available on carrier-mounted DSU/CSUs only.

▲

– This configuration option is not available if the ComExtDev configuration option is

set to AT or the communication port is disabled.

– ComEscDel must be configured for a delay greater than or equal to the escape

guard time required by the external device.

Table C-7.

User Interface Configuration Options (4 of 11)

«
...
185
186
187
188
189
...
»

Summary of Contents for 3165





























































































































































































































































































































Reviews:

No comments

Related manuals for 3165

Wireless Print Solutions Adapter

Brand: Xerox Pages: 54

Brand: DOREMIDI Pages: 4

Brand: Albrecht Pages: 32

Brand: AES Pages: 2

Brand: Sense Pages: 4

Brand: EtherCAT Pages: 74

Notebook Computer Universal 30W Power...

Brand: Radio Shack Pages: 36

Brand: Planet Pages: 72

Brand: Dante Pages: 2

Brand: Mini Gadgets Pages: 5

Brand: ViewSonic Pages: 69

WPN111 - RangeMax Wireless USB 2.0 Adapter

Brand: NETGEAR Pages: 2

Brand: Renkforce Pages: 4

Brand: Dell Pages: 49

EtherExpress Pro/10+

Brand: Dell Pages: 16

Brand: Dell Pages: 17

Brand: Dell Pages: 11

Brand: Dell Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands