10 |
Magellan & Spectra SP • Installation Guide
Keypads
Auditory Feedback
When you enter information on the keypad, it will guide you with beep tones that communicate confirmation or rejection of your entries. You should be familiar
with these two keypad beep tones:
Confirmation Beep
:
When an operation (e.g. arming/disarming) is successfully entered on the keypad or when the system switches to a new status/mode, the
keypad produces an intermittent beep tone (“
BEEP
-
BEEP
-
BEEP
-
BEEP
”).
Rejection Beep
:
When the system reverts to its previous status or when an operation is incorrectly entered on the keypad, it will emit a continuous beep tone
(“
BEEEEEEEEP
”).
The following are other types of auditory feedback, and will always be accompanied by the flashing of an arm key or LED (
[
ARM
]
,
[
STAY
]
, or
[
SLEEP
]
):
•
Continuous beep = Alarm
•
Variable beep = Fire alarm
•
Intermittent beep = Beginning of exit delay
•
Fast Intermittent beep = Last 10 seconds of exit delay
Visual Feedback
The keypad includes colored lights which convey the current status of your system. The state of each light represents a specific condition in your system.
NOTE:
Many of the features in your system must be enabled by the installer. If the feature is not programmed, the keypad will emit a rejection beep and the action
will be canceled. Refer to Zone Settings on page 5 for details.
Keypad Muting
When muted, the keypad will only emit the confirmation beep and rejection beep, and will beep when a key is pressed. Therefore, when muted, the keypad will not
beep during an alarm and will not beep for chime enabled zones. Each keypad must be muted separately.
How do I mute the keypad?
•
For K32+, K35, K37, K636, K10V and K10H:
Press & hold the [
CLEAR
] key for 6 seconds to enable or disable keypad muting. If the keypad emits a confirmation
beep, Keypad Muting is enabled for that keypad. If the keypad emits a rejection beep, the feature is disabled.
•
For the and K32LX:
Press and hold the [
] key for keypad settings. Press [4] for Mute Control. Press [arm] to enable or disable keypad muting.
Keypad Backlight
The illumination level behind the keys can be modified to suit your needs.
How do I modify the backlight?
•
For K32+:
Press and hold the
[
]
key. Press the
[
]
key to set the desired backlight level. Press
[
CLEAR
]
or
[
ENTER
]
to exit.
•
For K35:
Press and hold the
[
]
key for 4 seconds. Keys 1, 2, 3, 5 and 6 will flash. Press
[
CLEAR
]
to exit the menu without saving the information or press
[
ENTER
]
to exit the menu and save the information. Press the desired key and scroll using the
[
]
and
[
]
to adjust:
[1]
To adjust the scrolling speed.
[2]
To adjust the backlight (0 = Off, 1 = Lowest brightness / 7 = Maximum brightness)
[3]
To adjust the contrast (0 = Low contrast, 4 = High contrast)
[5]
To adjust the auto dim backlight level (0 = Off, 1 = Lowest auto dim backlight, (...) 7 = Highest auto dim backlight
[6]
To adjust the auto dim delay (0 = Off, 1 = 1 sec., 2 = 5 sec., 3 = 10 sec., 4 = 20 sec., 5 = 1 min., 6 = 2 min., 7 = 4 min.)
•
F
OR
K37:
Press and hold the
[
]
key for 4 seconds. Keys 1 and 2 will flash. Press
[
CLEAR
]
to exit the menu without saving the information or press
[
ENTER
]
to
exit the menu and save the information. Press the desired key and scroll using the
[
]
and
[
]
to adjust:
[1]
To adjust the backlight.
[2]
To adjust the auto dim delay (5 = 5 sec. / 15 = 15 sec.)
•
For the K10V, K10H and K636:
Press and hold the
[
MEM
]
key.
T
HE
[
MEM
]
KEY
WILL
ILLUMINATE
. P
RESS
THE
[
MEM
]
KEY
TO
SET
THE
DESIRED
BACKLIGHT
LEVEL
.
Press
[
CLEAR
]
or
[
ENTER
]
to exit.
•
For the and K32LX:
Press and hold the
[
]
key. Press
[2]
to modify the backlight. Scroll using the [
] and [
] keys. Press
[
ENTER
]
to save.
Power Save Mode (K37 only)
If DC power is not supplied to the wireless keypad, the module’s display will shut off and go into power save mode after one minute (20 seconds for K37). Press the
[ ]
key to activate the display.
