Pando Atlona Omega AT-OME-ST31A Manual Download Page 9

Page: 9 / 54

AT-OME-ST31A

OUTPUT

DC 24V

INPUT

RS-232

AT-OME-ST31A

AUDIO OUT

LAN

IP MODE

RESET

INPUT

PWR

LINK

OMEGA

AT-OME-ST31A

DISPLAY

OUTPUT

DC 24V

INPUT

RS-232

AT-OME-ST31A

AUDIO OUT

LAN

IP MODE

RESET

INPUT

PWR

LINK

OMEGA

AT-OME-ST31A

DISPLAY

Panel

Description

1 PWR Indicator

This LED indicator glows solid green when the unit is

powered.

LINK Indicator

This LED indicator glows solid yellow when an

HDBaseT link is established, between the AT-OME-

ST31A and the receiver.

Connect a mini-USB cable from this port to update

the firmware. Refer to

Updating the Firmware (page

46)

for more information.

4 INPUT button

Press and release this button to cycle through each

of the inputs. The LED indicators will display the

currently active input, and correspond to each of the

numbered inputs on the rear panel of the unit.

5 DISPLAY button

Press this button to power-on or power-off the

connected display.

6 IP MODE

Press and release this button to set the IP mode

or display the current IP address on the connected

display. Refer to

IP Configuration (page 13)

for

more information.

7 RESET

Press and release this button to reset the unit to

factory-default settings. Refer to

Resetting to Factory

Defaults (page 21)

for more information.

8 INPUT ports

Connect a USB-C cable from a video source to

INPUT 1

. Connect HDMI cables to

INPUT 2

and

INPUT 3

from HD/UHD sources.

9 OUTPUT ports

Connect an HDMI from the HDMI port to a display or

other sink device. Connect an Ethernet cable (CAT-

5e or better), from the HDBaseT port to a compatible

HDBaseT receiver. These ports are mirrored.

10 AUDIO OUT

Connect a 5-pin captive screw block to this port.

This port provides audio de-embedding of the source

to an audio output device.

RS-232

Connect the included 3-pin captive screw block to

this port. Refer to

Solution Setup and Configuration

Guide (page 35)

for more information.

LAN

Connect an Ethernet cable from this port to the

network.

13 DC 24V

Connect the optional 24 V DC power supply to this

power receptacle.

Front

Rear

Summary of Contents for Atlona Omega AT-OME-ST31A























































Search results

Summary of Contents for Atlona Omega AT-OME-ST31A

Reviews:

Pando Atlona Omega AT-OME-ST31A, Manual, Page: 9 / 54

Search results

Summary of Contents for Atlona Omega AT-OME-ST31A

Reviews: