18
Note that the total patrol time is two minutes, and the
time allowed for each routine depends on the number
of patrol routines that are configured. The values in
parentheses indicate the time of each patrol routine
(two minutes for one pattern, one minute each for two
patterns, 30 seconds each for four patterns).
If you want to change the number of patrol routines
from a previous setting, first delete all of the
currently store patrol routines. To delete everything,
move the cursor to RESET, and press the CAM
(SET) button.
3. Move the cursor to a PATROL number (PATROL 1
through 4), and then tilt the joystick left or right to
select a patrol setting.
---
:
Disables the selected patrol routine.
PLAY :
Performs the selected patrol routine. (see
this page)
LEARN :
Select this option to teach the camera a
series of movements (patrol routine). (An
asterisk (*) to the right of a PATROL number
indicates that it already has a patrol routine
assigned to it.) (see this page)
DEL
→
PUSH SET :
Press the CAM (SET) button to
delete an existing patrol
routine.
<When PLAY is selected>
(1) Press the system controller’s F2 button to close
the menu.
The orientation of the camera moves to the
stored start position, and the camera starts to
playback the stored movement.
(2) When the playback is finished, manually pan,
tilt, zoom and focus.
<When LEARN is selected>
(1) Press the system controller’s F2 button to close
the menu.
The start position is stored, and the camera’s
movements can be stored.
(2) Operate the camera to store the movements.
“LEARNING (***S)” is displayed in the centre of
the screen when the movements are being
stored. (unit: sec)
* “(***S)” indicates the amount of time that
remains for storing movements.
(3) The setup menu is displayed and teaching stops.
Storing movements stops when the remaining
time reaches “0S”.
Notes:
• Selecting LEARN to teach the camera a patrol
routine causes the following parameters to be
stored along with the camera movements.
(1) Parameters at the Beginning of the Routine
• PAN, TILT, ZOOM, and FOCUS positions
• IRIS level
• Shutter speed (SHUTTER)
• Gain (AGC) setting
• Electronic sensitivity enhancement (SENS
UP) setting
• White balance (WHITE BAL) setting
(2) During Camera Movement
• PAN, TILT, ZOOM, and FOCUS positions
• IRIS operation
• Preset positioning
• The auto-focus function does not work during
patrol operations. The image goes out of focus
when the camera zooms in from a wide angle
(WIDE), this is caused by the zoom lens
mechanism. The fuzziness in the image can be
reduced by starting from a telephoto angle (TELE)
when registering a zoom operation.
• In the patrol play mode, black and white
automatic switching does not work.
• In the patrol play mode, when the power of the
system controller is turned on or off, the patrol play
stops. In this case, press the PATROL PLAY button
again. (If SELF RETURN is set to ON, the patrol play
will start again after elapsing the setting return time.)
• Patrol movement covers a range from horizontal to
directly below the camera. The digital flip function
(page 20) does not operate.
• When you want to stop before the patrol memory
is finished, either click "STOP" when the system
controller is in LEARN mode or open the menu.
8
Privacy Zone Setting (PRIVACY ZONE)
The privacy zone function makes it possible to mask
specific areas of the scene (screen) from view. Up to
eight privacy zones can be configured.
Notes:
• Certain camera orientations can cause privacy
zone masked area to become visible.
• The privacy zone function does not mask scene
areas during the initialisation routine performed
immediately after camera power is turned on.
• The zone position may shift if the stabilizer
settings are change after setting the privacy zone.
1(2MIN)
↔
2(1MIN)
↔
4(30S)
**PATROL**
NUMBER
PATROL1*
PATROL2
PATROL3
PATROL4
RESET
RET TOP
4(30S)
PLAY
----
----
----
