Panasonic TH-43EQ2W Operating Instructions Manual Download Page 14

Page: 14 / 178

English

Remote Control Batteries

Open the battery cover.

Insert batteries and close

the battery cover.

(Insert starting from the

side.)

AAA/R03/LR03 type

Note

●

Incorrect installation of the batteries can cause

battery leakage and corrosion that will damage the

remote control.

●

Disposal of batteries should be done in an

environment-friendly manner.

Take the following precautions.

1.  Batteries shall always be replaced as a pair.
2.  Do not combine a used battery with a new one.
3.  Do not mix battery types (example; manganese

dioxide battery and alkaline battery etc.).

4. Do not attempt to charge, disassemble or burn used

batteries.

5. Do not burn or breakup batteries.

Moreover, batteries must not be exposed to excessive

heat such as sunshine, fire or the like.

Attaching the Function Board

When using a narrow-width function board, attach the

supplied SLOT adaptor, and insert it to the expansion

slot.

Note

●

Be sure to turn off the display unit and connected

devices, remove the power plug from the socket, and

disconnect the cables from the display.

●

When attaching/removing the function board, do not

allow the metal to damage the back cover or display

label.

When attaching a full-size function board, proceed to

step

Remove one screw from the side with

the guide on the SLOT adaptor.

SLOT adapter

Screw

Guide

Fit the circuit board of the function

board in the guides of the SLOT

adaptor, and bring the circuit board

into contact with the hook (one

location) and the end faces (two

locations) securely.

Function board

Hook

End face

Summary of Contents for TH-43EQ2W



















































































































































































Search results

Summary of Contents for TH-43EQ2W

Reviews:

Related manuals for TH-43EQ2W

Brands by name

Popular brands

Panasonic TH-43EQ2W, Operating Instructions Manual

Search results

Summary of Contents for TH-43EQ2W

Reviews:

Related manuals for TH-43EQ2W

Brands by name

Popular brands