Panasonic SC-HG1-C User Manual Download Page 65

Page: 65 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-31

4-8 Continuous reading of measurement data

If you want to continuously read judgment values, normal measured values, calculated values,

and sensor head values at once from all connected controllers, you can use a sensor response

data switching request to change to each mode and continuously read the values without the

need for commands.

Measurement mode

Description

Judgment value

Judgment values are read continuously.

Normal measured value Normal measured values are read continuously.

Calculated value

Calculated values are read continuously.

Sensor head value

Sensor head values are read continuously.

An example of reading judgment values when a master unit and slave units 1 to 3 are connected

is shown below.

is only set when the operation mode is CC-Link mode 1.

RX[7B] (*1)

Check remote ready flag

RX[08]

Check judgment value flag

RY[08]

Set judgment value flag

{RY[0B], RY[0A], RY[09], RY[08]} = {0,0,0,1}(*2)

{RX[0B], RX[0A], RX[09], RX[08]} = {0,0,0,1} (*2)

RWr[02] to [09]

Check sensor response data

(Master unit + 3 slave units)

Measurement data update cycle

First-time mea-

surement data

wait time

RX[7A] (*3)

Check error status flag

RY[10]

Page 1 settings
RX[10]

Check page 1 settings

Judgment value

{RY[0B], RY[0A], RY[09], RY[08]} = {0,0,0,1} (*2)

When operation mode is CC-Link mode 1

In case of judgment value

Check that RX[7B] (*1): remote ready flag is set.

Set the RY[08]: judgment value flag bit. Judgment value reading is requested and the

RX[08]: judgment value flag is set. Clear sensor response data switching request flags other

than the judgment value flag in advance.

The values will be as shown in the table below depending on the measurement mode that is

read.

Measurement mode

RY[0B]

RY[0A]

RY[09]

RY[08]

Judgment value

Normal measured value

Calculated value

Sensor head value

Summary of Contents for SC-HG1-C

































































































































Search results

Summary of Contents for SC-HG1-C

Reviews:

Panasonic SC-HG1-C, User Manual, Page: 65 / 128

Search results

Summary of Contents for SC-HG1-C

Reviews: