Panasonic SC-HG1-C User Manual Download Page 32

Page: 32 / 128

Installation and Settings

WUME-SCHG1C-4

3-10

3-3-5 Procedure for connecting the CC-Link connector

For the communication cable, use a CC-Link dedicated cable (shielded, 3-conductor, twisted pair

cable).

■

Communication cable work procedure

Strip off the jacket on the dedicated cable as shown below. When stripping off the jacket,

take care not to damage the shield braid inside the dedicated cable.

Outer jacket of dedicated cable

Shield braid

Approx. 50mm

Carefully unbraid the shield braid.

Firmly twist together the shield and the stranded wire inside the shield braid.

Cover the twisted shield wires with insulating tubing (obtain separately).

Insulating tube

(Obtain separately)

Shield braid

Strip off the stranded wire (lead wire) jackets as shown below.

Stranded wire (lead wire)

Approx. 3mm

Attach ferrule (sleeve) terminals (obtain separately) to the stranded wire (lead wire) and

shield wire.

Stranded wire (lead wire)

Ferrule (sleeve) terminal

(Obtain separately)

Summary of Contents for SC-HG1-C

































































































































Search results

Summary of Contents for SC-HG1-C

Reviews:

Panasonic SC-HG1-C, User Manual, Page: 32 / 128

Search results

Summary of Contents for SC-HG1-C

Reviews: