Panasonic PANAFAX DF-1100, Service Manual

Page: 156 / 333

Panasonic DF–1100
4–44
Information Codes
Code Cause Description of Problem Phase Mode
301
XMT
RCV
System fault. Software problem occurred (FCB PCB)
331 XMT C 8–minutes timer error. (Germany only)
400 XMT B
T1 timer (35
ࠡ
5 sec) elapsed without detecting
300 bps signal.
Wrong number is dialed and the START button
is pushed.
Telephone line is disconnected while dialing.
FCB PCB (Modem) or LCE PCB is defective.
Receiver is defective. (It may only be
transmitting CED)
401 XMT B
DCN was returned from receiver while
transmitter is waiting for CFR or FTT.
Your machine’s ID Number is not programmed.
Possible incompatibility or incorrect Password
(Password Reception, Selective Receive).
Mailbox is full.
402 XMT B
DCN was returned from receiver while
transmitter is waiting for NSF/DIS. Receiver working in non–CCITT mode only.
(Possible incompatibility)
403
RCV
(Polling)
B
Transmitter had no polling function.
”POLLED=ON” (polling XMT ready) is not set
at the transmitter.
Document to be transmitted is not placed at
the transmitter.
404 XMT B
Transmitter sent NSS (or DCS) followed by
TCF three times, but the receiver did not
respond. (CFR or FTT is usually returned)
Receiver is defective. (Modem, LCE PCB,
etc.)
FCB PCB or LCE PCB is defective.
Receiver disconnects line during first NSS (or
DCS) is transmitted.
405 XMT B
Transmitter received FTT after it transmitted
TCF at 2400bps.
Received RTN after communicating at 2400
bps.
Line quality is poor. (TCF is damaged due to
line noise)
Receiver is defective. (Modem, LCE PCB,
etc.)
FCB PCB or LCE PCB is defective.
406
RCV
(Password
Comm.)
B
XMT–Password mismatched.
RCV–Password mismatched.
Selective RCV incomplete.
XMT, RCV password does not match.
Last 4 digits of TSI does not match with the
last 4 digits of ONE–TOUCH, ABBR telephone
number.
407 XMT D
Transmitter received no response after it
transmitted post message, such as EOP, MPS,
EOM, etc.
Or received DCN.
Receiver is defective. (No paper, paper
jamming, etc.)
Receiver ceased receiving because of
excessive error. (Line quality is poor)
FCB PCB (Modem) or LCE PCB is defective.
408 XMT D
Transmitter received RTN after it transmitted
EOP, MPS, or EOM.
Receiver receives data with error. (Line quality
is poor)
Receiver is defective. (Modem, LCE, etc.)
FCB PCB or LCE PCB are defective.
409 XMT D
Transmitter receives PIN after it transmitted a
post message, such as EOP, MPS, EOM, etc.
Receiver receives data with error due to poor
line quality, and receiving operator requests
voice contact.
Receiver is defective. (Modem, LCE, etc.)
FCB PCB or LCE PCB are defective.
410 RCV D
Received DCN while waiting for post
command. (EOP, MPS, EOM, etc.) Interface or line is faulty.
Transmitter is defective.
411
RCV
(Polling)
B Received DCN after transmitting NSC.
Transmitter is not ready for polling
communication.
Password does not match between transmitter
and receiver.
412 G3 RX
B
D
No response within 12 seconds in
NSS/DCS/MPS wait state. (After transmitting
FTT, MCF, or CFR)
Transmitter is defective.
FCB PCB is defective.
414
RCV
(Polling)
B
No response received after transmitting 3rd
NSC.
Password does not match between transmitter
and receiver.
Transmitter is defective. (No document,
document jam, etc.)
415
XMT
(Polling)
B
Remote side attempted to receive message
from your machine in polling communication.
”Inform the remote side that your machine does
not have the polling transmission feature.”
416 RCV D
Receiver did not detect post command, such
as EOP, MPS, EOM, etc.
Transmitter is defective.
Line quality is poor. (RTC signal is distorted
due to line noise)
FCB PCB or LCE PCB are defective.