Panasonic PANAFAX DF-1100, Service Manual, Page: 173 / 333

Test Modes
5–7
Function Parameter Table
No. Function Selections Parameter (see Note3)
51 TONE DET MODE
1 = Normal
Selects quality of dial tone and busy tone detection.
Use if the line signals are out of regulation set “Rough”
51 TONE DET. MODE
2 = Rough
q y y
Use if the line signals are out of regulation, set “Rough”
so unit may detect the signals.
52 PULSE RATE
1 = 10 pps
Selects dial pulse rate 10/20 pps 52 PULSE RATE
2 = 20 pps
Selects dial pulse rate 10/20 pps.
TEL TYPE (Except for North
1 = Normal
Selects Normal, Invert or +1 dial pulse type.
53
TEL TYPE (Except for North
America version)
2 = Invert
Selects Normal, Invert or +1 dial ulse ty e.
Invert : Norway, New Zealand
S d
53
America version)
3 = +1
Invert : Norway, New Zealand
+1
: Sweden
54
INTNTNL DT MODE (For
Belgium France and Spain
1 = Off
Selects whether to distinguish the 4–digit international
54
(
Belgium, France and Spain
version only.)
2 = On
Selects whether to distinguish the 4–digit international
access code prefix.
55 BUSY TONE CHECK
1 = Off
Selects Busy Tone detection function 55 BUSY TONE CHECK
2 = On
Selects Busy Tone detection function.
56
DIAL TONE CHECK
(Except for USA and Canada
1 = Off
Selects whether to detect dial tone before dialing the
56 (Except for USA and Canada
version)
2 = On
Selects whether to detect dial tone before dialing the
telephone number.
57
DC LOOP CHECK
(Except for USA and Canada
1 = Off (will not check)
Selects whether the unit checks the DC Loop during
57 (Except for USA and Canada
version)
2 = On (checks)
Selects whether the unit checks the DC Loo during
communication.
58 COMM JRNL +IMAGE
1 = Off (without image)
Selects whether the machine prints the COMM. Journal
58 COMM.JRNL +IMAGE
2 = On (with image)
Selects whether the machine rints the COMM. Journal
with image.
59 CONF RCV REPORT
1 = Off (not printed out)
Selects whether the machine prints the CONF. RCV
59 CONF. RCV REPORT
2 = On (printed out)
Selects whether the machine rints the CONF. RCV
REPORT.
60 VERSION: Indicates ROM version.
61 TX/RX/PRT/CPY COUNTER TX/RX/PRT/CPY
Indicates transmitted, received, printed and total copied
document count.
62
ƞ
69
Not used
1 = 128 lines
1. Selects line disconnect condition during reception. If
2 = 256 lines
1. Selects line disconnect condition during rece tion. If
the number of line errors exceed this setting, the unit
ill di h li
70 LINE ERROR
3 = 512 lines
the number of line errors exceed this setting, the unit
will disconnect the line.
2 Selects transmit condition of RTP/PIP or RTN/PIN 70 LINE ERROR
4 = 1024 lines
2. Selects transmit condition of RTP/PIP or RTN/PIN.
(Available if No.73 ERROR DETECT is set to
5 = 2048 lines
(Available if No.73 ERROR DETECT is set to
“LINES”.)
(S N 1)
6 = Off (will not disconnect line)
LINES .)
(See Note 1)
1 = 5%
S l i di i f RTP/PIP RTN/PIN
71 TOTAL ERROR
2 = 10%
Selects transmit condition of RTP/PIP or RTN/PIN.
(Available if No 73 ERROR DETECT is set to “RATE” ) 71 TOTAL ERROR
3 = 15%
(Available if No.73 ERROR DETECT is set to “RATE”.)
(See Note 2)
4 = 20%
(See Note 2)
1 = 3 lines/STD
Selects continuous total error criteria of 3/6/12 lines or
72 CONTI ERROR
2 = 6 lines/STD
Selects continuous total error criteria of 3/6/12 lines or
Off as Standard mode. If continuous total error exceeds
72 CONTI. ERROR
3 = 12 lines/STD
Off as Standard mode. If continuous total error exceeds
this setting, the unit will transmit RTN/PIN. (Available if
N 73 ERROR DETECT i
t t “RATE” )
4 = Off (unlimited)
this setting, the unit will transmit RTN/PIN. (Available if
No.73 ERROR DETECT is set to “RATE”.)
73 ERROR DETECT
1 = Lines
Selects the error detect condition Lines/Rate 73 ERROR DETECT
2 = Rate
Selects the error detect condition Lines/Rate.
74 RTN RECEIVE
1 = Disconnect
Selects reaction when “RTN” is received 74 RTN RECEIVE
2 = Continue
Selects reaction when “RTN” is received.
1 = MH (MH only)
75 CODING
2 = MR (MH or MR)
Selects coding scheme. 75 CODING
3 = MMR (MH or MR or MMR)
Selects coding scheme.
76 Not used
77 Not used
78
FUNCTION TX (with Center
1 =Off
Selects whether the unit transfers the RAM data to the
remote station without Function parameter No 61 and
78
FUNCTION TX (with Center
ROM only)
2 =SYS (transfer RAM data)
remote station without Function parameter No.61 and
Journal Informations.
1 = Off
79
FUNCTION RX (with Center
ROM only)
2 = SYS (retrieve RAM data
without Journal Information)
Selects whether the unit retrievers the RAM data from
the remote station
79
ROM only)
3 = JNL (retrieve Journal
Information)
the remote station.
00 = 00 mm
Adjusts the distance between the scanning sensor ON
80 DOC TOP FEED
ƞ
Adjusts the distance between the scanning sensor ON
position and the scanning start position
80 DOC TOP FEED
99 = 99 mm
position and the scanning start position.
00 = 00 mm
Adjusts the distance between the scanning sensor OFF
81 DOC END FEED
ƞ
Adjusts the distance between the scanning sensor OFF
position and the scanning end position
81 DOC END FEED
99 = 99 mm
position and the scanning end position.