manualshive.com logo in svg

Panasonic KX-TDE600, Programming Manual

The Panasonic KX-TDE600 is a powerful and versatile communication system. To maximize its potential, a Programming Manual is indispensable. You can easily download the manual for free from our website, providing step-by-step instructions and helpful tips to optimize your user experience with this exceptional product.

Share
Download
background image

Value Range

Off, Fixed IP Addr., STUN

NAT - Voice (RTP) UDP Port No.

Specifies the starting port number of the dynamic ports used for NAT Traversal.

Default

16000

Value Range

2–65000 (even number only)

 NAT - Keep Alive Packet Sending Ability

Specifies whether to send Keep Alive packets in order to maintain the NAT binding information. This setting
may be compulsory depending on the network conditions.

Default

Disable

Value Range

Disable, Enable

NAT - Keep Alive Packet Type

Specifies the type of Keep Alive packets to be sent out.

Default

Blank UDP

Value Range

Blank UDP, None

NAT - Keep Alive Packet Sending Interval

Specifies the interval time until the next Keep Alive packet is sent.

Note

It is required to set this interval shorter than the NAT binding time of the router. The default value is
appropriate in most cases.

Default

20 s

Value Range

1–60 s

Document Version  2008-11  

Programming Manual for Virtual SIP CO Line Card

49

3.3.1 Main

Summary of Contents for KX-TDE600





























































Reviews:

No comments

Related manuals for KX-TDE600

Brands by name

Popular brands

Load more brands