Panasonic KX-TDE600 Programming Manual Download Page 46

Page: 46 / 60

DHCP Alternate DNS Server IP Address

Indicates the IP address of the alternate DNS server assigned automatically by the DHCP server (reference
only).

Default

Not stored.

Value Range

1.0.0.0–223.255.255.255

Manual Preferred DNS Server IP Address

Specifies the IP address of the preferred DNS server manually. This setting is compulsory if a DNS server IP
address is not assigned automatically.

Default

Not stored.

Value Range

1.0.0.0–223.255.255.255

Manual Alternate DNS Server IP Address

Specifies the IP address of the alternate DNS server manually.

Note

Manual Preferred DNS Server IP Address

is programmed, this setting is optional. However, if possible,

it is recommended to specify

Manual Alternate DNS Server IP Address

as well.

Default

Not stored.

Value Range

1.0.0.0–223.255.255.255

Manual DNS Server Port Number

Specifies the port number of the DNS server.

Default

Value Range

1–65535

DNS Port Number

Specifies the port number of the PBX used for communication with the DNS server.

Default

30053

Programming Manual for Virtual SIP CO Line Card

Document Version 2008-11

3.2.1 Card Property

Summary of Contents for KX-TDE600





























































Search results

Summary of Contents for KX-TDE600

Reviews:

Related manuals for KX-TDE600

Brands by name

Popular brands

Panasonic KX-TDE600, Programming Manual

Search results

Summary of Contents for KX-TDE600

Reviews:

Related manuals for KX-TDE600

Brands by name

Popular brands